Indexa-Seiki Standard Pull Studs

BT-MAS 403

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100

Dormer Stub Drills

A920 - HSCo PFX Stub Drills
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow.Size Range: 1.0-20.0mm. Manufactured to BS 323, DIN1897, ansi.

A920 - HSCo PFX Stub Drills - metric

A920
Excellent for:
Carbon/alloy steels, stainless, titanium and nickel

Good for:
Cast iron, copper, aluminium and thermoplastics

VBMT

Suitable for External Toolholders.

Guhring Production Jobber Drills HSS-Co 5%

Rigid, high-heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. Limited suitability for special alloys such as hastaloy, inconel, nimonic etc. Manufactured to DIN338.

Series 605 - Metric

Sherwood Machine Reamers

Sherwood machine reamers are used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head.

Conform to BS 122 : Part 2 and BS 328 Part 4.

For all technical and dimensional specifications please refer to our catalogue.

Machine Reamers Taper Shank HSS - Metric

Sherwood Long Series Drills Steam Tempered HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

SwissTech High Helix Quick Spiral Drills for Aluminium HSS-Co 8%

High helix drills, to drill long-chipping materials like aluminium, aluminium alloys, copper and plastics. Point angle: 130. Helix angle: High. Web thickness: Normal. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufactured to DIN338RN.

Series 1012 - Metric

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Gauge Sizes

Saw Blades HSS

These cutting off super HSS blades are recommended for use on all automatic production saws and manually operated machines where long life and high output is essential. All dimensions are within tolerances stipulated by ISO or DIN.

For all technical and dimensional specifications please refer to our catalogue.

Cutting Off Blades HSS