Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Cranked Round Nosed Turning Tools

Right Hand. Available in Grades P30 and K20.

Swiss+Tech® HSS "Green Ring" Taps

Manufactured to DIN 371/376.

Spiral Flute - HSS-EV Nitride Finish ISO Metric Coarse

For blind holes. Taper lead to DIN form C (2.5 x P). Tapping tolerance to 6H 2B. Helix angle 45°. Tapping depth 2.5 x D.

Kennedy Toolbits

HSS Round Inch.

Collets

For use with Autolock chucks to hold shank milling cutters.

Indexa-Seiki? "Tri Square" Milling Cutters

Uses top clamping triangular inserts to produce a 90 shoulder at the edge of a milled face. This is of major benefit when taking a number of cuts across a face as the shoulder produced is without steps.

Guhring Drills Taper Shank HSS-Co 5%

High heat resistant drill for drilling alloyed and unalloyed steels and castings with a tensile strength over 800N/mm2. Especially suitable for hot and cold rolled steels as well as case hardening and heat treatable steels. Manufactured to Type N DIN345.

For all dimensional specifications please refer to our catalogue.

Series 345 (MT2) - Metric

Indexa-Seiki? Lever Lock External Toolholders

For further technical and dimensional specifications please refer to our catalogue.

PWLN - Right Hand

95 Approach for negative 80 trigon inserts.

Dormer Solid Carbide Drills

The new Dormer MP-X range of multi-application carbide drills are cost effective, high performance drills that offer high productivity and supreme value for money. A wide range of materials can be machined using a minimum number of drills, to reduce stock-holding and associated costs.

MP-X Solid Carbide Drills

Dormer MP-X solid carbide drills deliver the following benefits and features:

Benefits
? Exceptional value with no compromise on quality.
? High productivity.
? Excellent hole quality.
? Availability.
? Reduced tooling costs.

Material
Micro-grain carbide for an excellent combination of hardness and toughness, resulting in high wear resistance and longer tool life.

Coating
Multi-layer titanium aluminum nitride (TiAlN) coating gives:
? Improved stability of cutting edges.
? Outstanding wear protection.
? High hardness properties.
? High toughness and oxidation stability
? Longer tool life and higher productivity.

Flute Geometry
Strong web design gives excellent crosssectional strength and facilitates chip evacuation.

Point Geometry
140 point angle with good centring capabilities and low thrust force design, suited to multiapplication drilling.

Multi-Application
Multi-application drilling across a wide range of materials, including:
? Carbon and alloy steels.
? Stainless steels.
? Cast iron.
? Aluminium.
? Magnesium alloys.
? Copper.

Suitable for Regrinding
The quality of design will allow consistently high levels of performance and tool life after the product is reconditioned, providing further cost reduction benefits.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Taper Tap UNF (Unified Fine) Straight Flute Ground Thread HSS

Sherwood taper taps are used to start cutting the thread is tapered back from the end 6 to 10 threads before a fully threaded diameter is reached this allows the tap to be positioned easily and correctly before it starts to cut the thread.

Sherwood Quick Spiral High Helix Drills HSS

High helix drill for drilling materials like aluminium, aluminium alloys, copper and soft plastics. Point angle 130, helix angle: high, web thickness: standard, relief angle: normal, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328:Part 1:1986.

Series J300