Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute - Inch

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16" - 1/4" 0.000 -0.002
17/64" - 1" 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080

OSG Endmills Carbide

OSG WX-EMS short series 4 flute endmills are manufactured from high performance micro grain carbide with an Ultra WX coating (multi layered composite TiALN).

Centre cutting.
Cutting length: 1.5 x D.

The Ultra WX coating has been developed to improve performance in a wide range of materials including nonferrous materials, mild steels, and refined steels This stable performance remains consistent in both wet and dry applications and is intended for a wide range of cutting conditions, from low speed/reduced cutting force applications to high speed/high cutting force applications.

For all technical and dimensional specifications please refer to our catalogue.

WX-EMS Series 4 Flute Endmill 30 Helix Plain Shank Carbide

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Second Tap BA (British Association) Straight Flute Ground Thread HSS

The Sherwood second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before a fully threaded diameter is reached. If threading a blind hole a Plug tap will be required to cut threads to the bottom of the hole.

Granlund Size 1 Pilots

Type RS Roller Tol. c9.

When working 'dry' type R roller pilots must be lubricated. Pilots type RS must be combined with holders type AS.

For all technical specifications please refer to our catalogue.

Guhring Stub Drills Carbide SL

Carbide drills deliver a quantum leap in high speed holemaking performance and tool life that manufacturers have been asking for. Carbide tooling provides faster cutting rates, longer tool life, better positional and dimensional accuracy and improved surface finish. Short cycle times and tighter tolerances translate into maximum machine utilizations, better part quality and optimum holemaking cost savings.

Series 5516

Kennedy® Industrial Drill Chuck Arbors

Precision machined, fully hardened & ground to give maximum surface contact.

Morse Taper Drive to Jacobs Taper

Mitsubishi GY Series Parting & Grooving Holders & Blades

The Mitsubishi GY series of grooving and parting off toolholders are a range of tools designed to offer ultimate rigidity and accuracy for stable grooving applications.

The modular system allows flexible tool selection while maintaining overall strength for stable machining. Additionally, a wide variety of inserts makes it possible to cover a diverse range of machining applications, ensuring high efficiency, high precision machining.

GY Series 90 Face Grooving Right Hand Modular Blade

For producing 3.00mm Groove width.

Starrett Bi-Metal Holesaws Constant Pitch HSS

Bi-Metal Constant Pitch Holesaws have 6 teeth per 25mm/inch with an aggressive cutting action, featuring a HSS cutting edge welded to a tough alloy steel body. The Constant Pitch provides a smooth cut on thinner gauge materials, with minimal tendency to bite or snag on contact with irregular surfaces. Cutting depth 41mm (1 5/8").

Holesaw and Arbor sizes:
14-25mm - use Arbor A4 or K4.
30-210mm - use Arbor A10 or K10.

Constant Pitch Bi-Metal HSS Holesaws

SwissTech 3 Flute Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 07 Long SDL-3WL TiALN Coated

Dimensions to DIN 844.