Kennedy Holesaws Constant Pitch Bi-Metal HSS

Featuring a constant pitch - first choice for cutting thin sheet materials up to 3mm thick. For producing high quality holes in wood, steel, brass, bronze, cast iron, aluminium and plastic. Featuring an hardened HSS cutting edge welded to a tough alloy steel body. Heavy duty shatter-resistant construction; virtually unbreakable.

6 teeth per inch.
38mm (1,1/2") cutting depth.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

For the complete range of Holesaws and Arbors, please refer to our catalogue.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Starrett Bandsaw Blades

Made from carbon steel with a flexible back, Duratec™ SFB is ideal for economical cutting on easy-to-machine ferrous or non-ferrous metal and wood.
Features: Flexible carbon steel back. Wide range of widths, thickness and pitches.
Benefits: Blades can be run at higher band speeds than standard bi metal blades.
Economical general purpose cutting. Ideal for both contour & straight cutting.
Suitable for light vertical and horizontal machines.
Applications: Wood, plastics.
Non-ferrous foundry materials.
Low alloy and non-ferrous metals.
Furniture, composition board.

Mitsubishi Indexable Milling Inserts

Mitsubishi grade description: VP30RT (P30-P45/M30-M45) PVD ''Miracle'' Coated Milling Grade. Offers increased heat resistance and adhesion strength. For all Steels and Stainless Steel

JDMW Indexable Milling Insert

Sandvik CoroKey Indexable Turning Inserts

Sandvik CoroKey H13A grade description:
(HW) K20 (K10-K30) Uncoated. A grade for medium to rough turning of heat resistant steels and titanium alloys and a good choice for roughing of cast iron

CNMG Turning Insert

Sandvik CoroKey chipbreaker description: QM - Negative insert - Large application area for semi-finishing to light roughing in different materials.

Starrett Bandsaw Blades

Made from carbon steel with a flexible back, Duratec™ SFB is ideal for economical cutting on easy-to-machine ferrous or non-ferrous metal and wood.
Features: Flexible carbon steel back. Wide range of widths, thickness and pitches.
Benefits: Blades can be run at higher band speeds than standard bi metal blades.
Economical general purpose cutting. Ideal for both contour & straight cutting.
Suitable for light vertical and horizontal machines.
Applications: Wood, plastics.
Non-ferrous foundry materials.
Low alloy and non-ferrous metals.
Furniture, composition board.

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Inch

For all dimensional specifications please refer to our catalogue.

SS-Co 5% 3 Flute Piloted Countersinks

For the production of high precision concentrically centred countersinks in most metals where pilot holes have been pre-drilled.
Shank diameter: 3/16”.

SwissTech 3 Flute Slot Drills Weldon Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Cutting diameter to e8. Shank diameter to h6. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 06 Regular SDN-3WR TiCN Coated

Dimensions to DIN 844.

Indexable Toolholder Sets

Supplied complete with 10 Carbide inserts,in a choice of P Grade for steels and general use, or K Grade for cast iron and non-ferrous applications.

Inserts supplied will vary according to availability.

MVJN R

93 approach. Uses VN_A & VN_G Inserts. For toolholder details see IND-106-1500P/-1520K