Granlund HSS Size 1 Countersinks

Type T. HSS. Tolerance x9 90.

Countersink T with a diameter 50mm and larger are made with a driving lip. These sizes should be used in the appropriate type M holder.

For further specifications please refer to our catalogue.

Sherwood Ground Thread Chasers HSS

Used for the lathe turned production and repair of threads.

For all technical specifications please refer to our catalogue.

Hand

ISO Metric Form

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Guhring Stub Drills HSS

Ideally suited for portable drill applications where the shorter flute and stub length offer the extra rigidity normally associated with fixed drilling. Manufactured to BS328:Part 1:1986/DIN1897RN.

Series 223

Dormer Jobber Drills TiN Tipped

Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.

Series A002

SwissTech 4 & 6 Flute End Mills Threaded Shank HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B.
Shank cutting diameter to plus0.04 -0.0.

Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 37 Long EMH-4TL HSS-Co 8%

Dimensions to DIN 844.

OSG Endmills Carbide

OSG WX-EBD series ball nose endmills have a long plain shank and an extended neck for hardened material. High performance micro grain carbide with Ultra WX coating (multi layered composite TiALN).

For use on material up to 50HRC.
For ultra high-speed machine centres.
For deep slotting. Cutting length: 0.8 x D.

The Ultra WX coating has been developed to improve performance in a wide range of materials including nonferrous materials, mild steels, and refined steels This stable performance remains consistent in both wet and dry applications and is intended for a wide range of cutting conditions, from low speed/reduced cutting force applications to high speed/high cutting force applications.

For all technical and dimensional specifications please refer to our catalogue.

WX-EBD Series 2 Flute Ball Nose Endmill Plain Long Shank Carbide

Sherwood Jobber Drills Bright Finish HSS

General-purpose drills for steel, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328/DIN338RN. Bright finish: drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.

Series J100 - Metric - Bright Finish

M42 Bi-Metal Bandsaw Blades

Starrett Powerband Gladiator M42 is the ultimate competitor in bi-metal bandsaw blades, providing a universal solution with optimum efficiency in large production cutting operations. A high speed steel M42 cutting edge, incorporating a new tooth design with a positive rake angle and variable pitch, combine to give Powerband Gladiator? M42 the utmost in cutting performance and cost effectiveness.

Powerband Gladiator Welded Loops

Recommended applications for Starrett Powerband Gladiator M42 bandsaw blades:
- High production cutting, full range of steels from mild to stainless up to 45 HRC, nickel-based and non-ferrous alloys
Features and Benefits:
- New tooth design features triple-tempered
- M42 high speed steel with 8% cobalt
- Rockwell C67-69
- Up to 12 positive rake angle
- Fatigue resistant alloy steel backing strip
- High wear and heat resistance
- Variable pitch teeth reduce vibration for smooth, quick cutting
- Easy penetration, excellent chip clearance, reduced noise levels
- Improved surface finish
- Faster, straighter cuts

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 1.0-16.
(D)26mm x (L)35mm.

ER25