Duratec™ SFB - formerly known as Super Flex-Back

Made from carbon steel with a flexible back, Duratec™ SFB is ideal for economical cutting on easy-to-machine ferrous or non-ferrous metal and wood.
Features: Flexible carbon steel back. Wide range of widths, thickness and pitches.
Benefits: Blades can be run at higher band speeds than standard bi metal blades.
Economical general purpose cutting. Ideal for both contour & straight cutting.
Suitable for light vertical and horizontal machines.
Applications: Wood, plastics.
Non-ferrous foundry materials.
Low alloy and non-ferrous metals.
Furniture, composition board.

Sherwood Long Series Drills Steam Tempered HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

Dijet Carbide End Mills

Dijet AL-SEELS series End Mills are for profiling & Slotting in Aluminium and Alloys

AL-SEEL-2 Long Series Carbide End Mill

Dijet AL-SEELS series Carbide end mill specification:
Sharp corner.
Helix angle 45.
2 flute.
Centre cutting.
Regular cutting edge.
Shank cutting diameter to 0.04-0.0
Weldon shank to DIN 1835B.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Short Series - Metric

Coventry Type Chaser Dies

Coventry high speed steel chaser dies are ideal for batch work or continuous production of threaded steel bar.

For all technical specifications please refer to our catalogue.

HSS Chaser Dies

ISO Metric

Sherwood® Slitting Saw Blades

Sherwood® HSS slitting saws are used for cutting metal, these small diameter saws are hollow ground to give the clearance necessary for deep cutting.

Sizes up to 1" diameter do not have key ways.

For all technical and dimensional specifications please refer to our catalogue.

Slitting Saw Small Diameter HSS

Guhring Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series 245 (MT1) - Metric

Dormer Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A100

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Metric

For all dimensional specifications please refer to our catalogue.