Dormer Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series A100

Dormer Jobber Drills Solid Carbide

General-purpose carbide drills. 120 four-facet point for accurate centering and improved hole quality. Bright finish.

Series R100 - Metric

Dormer HSCO Jobber Drills

A901 HSCo PFX Alcrona Top Jobber Drill
High productivity "one-hit" drilling to 6xD
Alcrona Top coating for extended tool life.
Excellent performance across a wide range of materials.
Size Range: 1.5 - 16.0mm, 1/16” - 5/8”

Dormer HSS 90 Spotting Drills

A122
Excellent for machine use and hand held tools on mild Steel,
cast Iron, copper, brass and aluminium. Fully ground (DIN 1897) and complete with a standard bright surface finish. 90 point, for hole depths up to 1x the diameter.

HSS 90 Spotting Drill - Series A122 - Metric

Dormer Jobber Drills TiN Tipped

Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.

Series A002

Dormer HSCO Jobber Drills

A941 (10xD) - 1.0-16.0mm, 3/64-5/8 Inch

A941 Long Series HSCO Jobber Drills Coated

A941
Excellent for: Carbon/alloy steels, stainless, cast iron and aluminium
Good for: Titanium and copper

Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Metric

EX00 TiN DIN 371 Spiral Flute Metric Taps

Titanium Nitride
Tolerance: 6H

Dormer Carbide Stub Drills

R120 - Carbide Stub Drill
For general carbide drilling applications.
120° four-facet point for improved accuracy & hole quality.
Bright Finish. Size Range: 1.0-12.0mm. Manufactured to BS 323, DIN6539.

EP00 TiN DIN 371 Spiral Point Metric Taps

Titanium Nitride Finish
Tolerance: 6H