Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Cranked Knife Turning Tools

Right Hand. Available in Grades P40, P30 and K20.

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Long Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% TiN Coated - Metric

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Kennedy® Jobber Drills Solid Carbide

For drilling steels, cast steels, cast iron, chilled cast iron, malleable cast iron, non-ferrous heavy and light metal and abrasive plastic. Point angle 118°. Tolerance of diameter: h7. Tolerance of shank: h6. Supply unit. All diameters - 1 pce. Manufacturing Standard: DIN 338, BS 328.

Metric

Kennedy® Long Series Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 4 Flute Slot Drills - Metric

Centre cutting as standard. For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16 - 1/4 0.000 -0.002
17/64 - 1 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080
Long Series

Kennedy® High Performance Machine Taps

Made from a super grade high speed steel with extra vanadium content. This has a distinct advantage with taps, by increasing wear resisting properties and extending tool life significantly. These taps are intended for general application where consistent results and improved tool life are important. Threads can be produced in a range of steels, including stainless and cast steels as well as some long chip non-ferrous materials.

Machine Taps Spiral Flute Metric Coarse HSS - EV

With high helix (45°), right hand spiral flutes, designed to pull swarf towards the shank of the tap. Most suitable for blind-hole tapping. Manufactured to BS 949 : Part 4 : 1990 and ISO 529 : 1975. Tolerance 6H.
Bright finish: standard finish for tapping most materials including low silicon aluminiums, brass, mild steels (low volume) stainless, copper.

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

2 Flute
For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non-ferrous and other soft materials. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 2 Flute Slot Drills - Metric

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric

Kennedy Holesaws

Kennedy holesaw arbors are manufactured from alloy steel that is precision machined and threaded, to guarantee a smooth secure fit to all Kennedy variable, constant pitch or carbide tipped holesaws* and are designed to ensure that you can quickly change the hole saw or HSS pilot drill.

Available with hexagon, round and SDS-plus shanks suitable for use with all power tools and are also compatible with all other popular threaded bore hole saws.

For the full range of Kennedy holesaws and arbors please refer to our catalogue.

*When used with the correct size of holesaw.

K1 14-30mm Holesaw Arbor

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.