Kennedy Precision Hand Files Industrial Quality

Engineers? Hand files have parallel edges, one edge uncut. For flat filing, corner filing and deburring. Multi-purpose and for other work where a ?safe? or uncut edge is needed. Double cut. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Hand

Available in Cut 0, 2 and 4.

Kennedy Engineers' Hand Files Industrial Quality

Engineers' Flat Files have edges that taper towards front. Applications as for hand files but without safe edge. Preferred where taper allows access into tight corners and angles. For general work on iron, steel, etc. Available as Smooth Cut, Second Cut and Bastard Cut.

Flat

Smooth Cut

Kennedy® 2 Flute Milling Cutters for Aluminium Carbide Al-Karb Ultrafine Micrograin

Centre cutting as standard. An advanced tool geometry designed for cutting aluminium and other non-metallic, non-ferrous materials requiring high machining rates. Al-Karb cutters will out-perform conventional end mills on these materials as the flute design allows maximum chip removal.Short Series

Short Series 2 Flute - Inch

Kennedy® Milling Cutters Throwaway Micro-Grain Solid Carbide

For high volume production. Compatible with standard automatic locking chucks and spindle adaptors (available on request).

Long Series - Metric

Carbide Tipped Holesaws

Kennedy carbide tipped holesaws last up to 10 times longer than standard hole saws and resist wear and heat caused by friction much better than traditional holesaws, making them the best choice for cutting tough material such as tile, stainless steel.

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Holesaws Carbide Tipped

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute - Inch

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16" - 1/4" 0.000 -0.002
17/64" - 1" 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

3 Flute
Centre cutting as standard. Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 3 Flute Slot Drills - Metric

Kennedy® High Performance Machine Taps

Made from a super grade high speed steel with extra vanadium content. This has a distinct advantage with taps, by increasing wear resisting properties and extending tool life significantly. These taps are intended for general application where consistent results and improved tool life are important. Threads can be produced in a range of steels, including stainless and cast steels as well as some long chip non-ferrous materials.

Machine Taps Spiral Flute Metric Coarse HSS - EV

With high helix (45°), right hand spiral flutes, designed to pull swarf towards the shank of the tap. Most suitable for blind-hole tapping. Manufactured to BS 949 : Part 4 : 1990 and ISO 529 : 1975. Tolerance 6H.
Bright finish: standard finish for tapping most materials including low silicon aluminiums, brass, mild steels (low volume) stainless, copper.

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Square Inch

Kennedy® Stub Length Drills Carbide

For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic. Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6. Manufactured to DIN 6539.

Tolerances:
Cutting Dia. plus 0.000mm - 0.015mm.
Shank Dia. plus 0.000mm - 0.030mm.

Kennedy® Carbide Stub Length Drills - Metric