Kennedy Rotary Masonry Drill Bits

Tungsten carbide tipped with roll forged flutes. A general-purpose mortar and masonry drill bit suitable for workshop and maintenance. Manufactured to DIN 8039.

Extra Length

Available in 300mm to 400mm length.

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

4 Flute
Centre cutting as standard. For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute End Mills - Metric

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Kennedy High Performance Rotary Impact Drill Bits

Tungsten carbide tipped with fully ground flutes. Full flute width, tip seating and specially designed cutting angles. For rapid drilling of concrete, brick, masonry, etc. Suitable for both rotary and rotary-impact use. Manufactured to BS 5621: 1992, ISO 5468 : 1992.

Medium Length

Kennedy Toolbits

HSS Round Inch.

Kennedy Needle Files Industrial Diamond-Coated 16cm

Available in seven shapes, Hand, Half Round, Three Square, Round, Square, Knife and Flat and two grain sizes, 120/140 and 325/400 offering the solution to finishing problems where material hardness makes conventional files ineffective. Plated with finely selected diamond powder, 120 - 150 mesh. Can be used on tungsten carbide, ceramics, carbon, glass, fibreglass and hardened steels such as stainless steel, nimonics, titanium etc.

Square

Kennedy® Stub Length Drills Carbide

For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic. Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6. Manufactured to DIN 6539.

Tolerances:
Cutting Dia. plus 0.000mm - 0.015mm.
Shank Dia. plus 0.000mm - 0.030mm.

Kennedy® Carbide Stub Length Drills - Metric

Kennedy® Ball Nosed Slot Drills Plain Shank Carbide Micrograin

Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Chatter is also significantly reduced. Centre cutting as standard. Manufactured to Ansi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 3 Flute - Inch

Kennedy® Long Series Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 2 Flute Slot Drills - Metric

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

4 Flute
Centre cutting as standard. For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute End Mills - Inch

Centre cutting as standard. Offer a combination of advantages achieved with two and four flutes giving profile and peripheral milling capability in addition to slotting and plunging. Manufactured to Ansi Standards.
Inch Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1/16 - 1/4 0.000 -0.002
17/64 - 1 0.000 -0.003
Metric Tolerances
Nominal Limits Of Tolerance
Diameter High Low
1 - 6 0.000 -0.050
7 - 25 0.000 -0.080
Regular Length