Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

HSS Square Inch

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric

Kennedy Engineers' Hand Files Industrial Quality

Parallel edges, surfaces taper towards point. For groove, rectangular hole and internal corner filing. Preferable to a Flat File because of its heavier section. Available as Smooth Cut, Second Cut and Bastard Cut.

Square

Bastard Cut

Kennedy Precision Hand Files Industrial Quality

Diameter tapers towards point. Suitable for internal and external concave surfaces. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Round

Available in Cut 0, 2 and 4.

Kennedy Precision Hand Files Industrial Quality

Parallel edges, surfaces tapered towards end. Narrow version of hand file. For use where access is restricted. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Pillar

Available in Cut 0, 2 and 4.

Kennedy Multi Flute Rose Pattern Straight Shank Countersinks

Manufactured from M35 HSS and used for the deburring and chamfering of most metals and plastics.
Straight shank, ground flute.
Manufactured to BS328:Part 5:1983.

For all dimensional specifications please refer to our catalogue.

90° Degrees

Kennedy Precision Hand Files Industrial Quality

Diameter tapers towards point. Suitable for internal and external concave surfaces. Available in tanged pattern 100mm (4") and 150mm (6") lengths. Manufactured to BS 498: 1990.

Round

Available in Cut 0, 2 and 4.

Kennedy Needle Files Industrial Diamond-Coated 16cm

Available in seven shapes, Hand, Half Round, Three Square, Round, Square, Knife and Flat and two grain sizes, 120/140 and 325/400 offering the solution to finishing problems where material hardness makes conventional files ineffective. Plated with finely selected diamond powder, 120 - 150 mesh. Can be used on tungsten carbide, ceramics, carbon, glass, fibreglass and hardened steels such as stainless steel, nimonics, titanium etc.

Three Square

Kennedy® High Performance Machine Taps

Made from a super grade high speed steel with extra vanadium content. This has a distinct advantage with taps, by increasing wear resisting properties and extending tool life significantly. These taps are intended for general application where consistent results and improved tool life are important. Threads can be produced in a range of steels, including stainless and cast steels as well as some long chip non-ferrous materials.

Machine Taps Spiral Point Metric Coarse HSS - EV

With straight flutes and short fluted helix at point. Ideal for tapping through holes as swarf is directed ahead of the tap. Flutes are narrower than those of taps required to pull swarf towards the shank and act as lubricant channels, giving greater tap rigidity. Manufactured to BS 949: Part 4: 1990 and ISO 529 : 1975. Tolerance 6H.
Oxidised finish (black): special heat treated finish gives resistance to rust and reduces metal to metal friction. Combined with a porous surface that gives optimum lubricant retention, work-generated heat is minimised, giving prolonged cutting edge life. Use on higher carbon steels cast materials high silicon aluminiums.

Kennedy Heavy Duty Drills for Stainless Steel HSS-Co 8%

Heavy-duty drill made of 8% cobalt material with excellent heat resistance. To drill steels with tensile strength up to 1,400 N/mm2, very hard bronze, stainless steels as well as heat and acid resistant steels. Point Angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufacturing Standard: DIN338.

HSCo Heavy Duty Drill For Stainless Steel - Series XT34 - Metric