Kennedy Precision Hand Files Needle Pattern (Round Handle)

Available in 14cm and 16cm lengths and a complete range of shapes. Manufactured to BS 498:1990.

Hand

Available in Cut 0, 2 or 4.

Kennedy® Long Series Slot Drills Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non ferrous and other soft materials. Manufactured to USCTi Standards.

For all dimensional and technical specifications please refer to our catalogue.

Long Series 2 Flute Slot Drills - Metric

Kennedy Toolbits & Parting-Off Blades

Cut faster, 'stand up' longer and reduce costs. Square and rectangular toolbits supplied with 10 bevelled ends. Parting off blades supplied with 2 side taper, 15 bevel (top and bottom).

5% Cobalt Square Metric

Kennedy Hacksaw Blades Flexible Back Bi-Metal

The perfect combination of shatter resistant spring steel, used as the backing material, and tough, wear-resistant HSS teeth - Electron-beam welded together. Ideal for interrupted cuts in cramped places or where the blade is subject to stress caused by twisting or bending. Provides optimum tooth strength/life and reduced breakage and fracture when compared to traditional all-hard blades. Made to BS 1919 : Part 1: 1993.

Kennedy 3Fl Countersinks HSS-Co 5%

Manufactured from M35 HSS and used for the deburring and chamfering of most metals and plastics.
Straight shank, ground flute.
Manufactured to BS328:Part 5:1983.

For all dimensional specifications please refer to our catalogue.

90° Degrees

Kennedy Toolbits

5% Cobalt Round.

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

4 Flute
Centre cutting as standard. For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute End Mills - Metric

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Cranked Turning Tools

Right Hand. Available in Grades P40, P30 and K20.

Kennedy Endmills

Kennedy KC3 throwaway 3* flute endmills are manufactured HSS-Co 5% making them much tougher than HSS. This means that Kennedy endmills can be used at higher speeds and feeds which in turn gives greater productivity.

Kennedy KC3 endmills are available uncoated, TiN coated and TiCN coated.

TiN (Titanium nitride) provides a surface hardness in the region of 2300HV which offers improved wear resistance, tool life and productivity.

TiCN (Titanium Carbonitride) gives a surface hardness in the region of 3000-3500 HV, excellent wear resistance and good heat resistance. This coating is used for the same things as TiN but also for hard steels, stainless, cast iron, brass & bronze.

For all technical and dimensional specifications please refer to our catalogue.

*Except: 1mm cutters, 2mm and 1/16" ball nose cutters, all of which have two flutes.

KC3 Endmill Short Series 3* Flute Throwaway Cutter Weldon Shank HSS-Co 5% TiN Coated- Metric

Kennedy® Milling Cutters Plain Shank Carbide Micrograin

2 Flute
For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non-ferrous and other soft materials. Manufactured to Works Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 2 Flute Slot Drills - Metric