Sherwood 2 Flute Long Series Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright Finish. Flute Type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional specifications please refer to our catalogue.

Metric

Sherwood 4 Flute Ball Nosed End Mills Plain Shank Solid Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute Ball Nosed End Mills

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.

Die Nuts Metric Fine HSS

Sherwood Gauge Drills HSS Steam Tempered

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle: 118, helix angle: normal, web thickness: standard, relief angle: 8 - 20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to ANSI B328, BS 328 and DIN 338.

Number & Letter Gauge Drills:
Gauge drills are still in common use in the U.S. In the past, they were popular elsewhere, but now have been largely discarded in favour of metric sizes. When using a gauge rather than a standard measurement of size the user has to refer to a table of gauge sizes. For example, to drill a hole which is 10 thou (thousandth of an inch .0010) bigger than a 1/8 inch bolt, the user must first work out that 1/8 inch is 125 thou, so the hole size needed is 135 thou, and then must look up in a reference book which gauge drill bit is closest to this diameter - a number 29. Number gauge sizes are similar or equivalent in some respects to, but different from, American wire gauge. Number gauge is usually used from size 80 (the smallest) to size 1 (the largest) followed by letter gauge size A (the smallest) to size Z (the largest). Number gauge is actually defined down to size 97, but these smaller sizes are rarely encountered. It happens that as the technology for making small drill bits and drilling small holes has become more available, metric drills have become the norm.

For all dimensional and technical specifications please refer to our catalogue.

Series J100 - Gauge Sizes

Sherwood Stub Drills HSS

General-purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118, Helix angle: Normal, Web thickness: standard, Relief angle: 10-20, Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to BS328:Part 1:1986/DIN338.

Series S100

Sherwood Die Nuts

Sherwood ground thread die nuts are suitable for repairing damaged or crossed threads and clearing swarf from threads. When using a die nut (on an existing thread) it is not necessary to apply the same level of precise initial alignment required to form a new thread (i.e. with a die) as the nut will follow the existing threads. They are supplied as hexagon drive allowing them to be turned by a standard spanner or adjustable wrench without the need for a special stock.

Conform to: ISO 529

For all technical and dimensional specifications please refer to our catalogue.

Die Nuts BSP(F) (British Standard Pipe Fittings) Ground Thread HSS

Manufactured to: BS1127
Thread Form to: BS21

Sherwood Stub Drills HSS

General-purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118, Helix angle: Normal, Web thickness: standard, Relief angle: 10-20, Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to BS328:Part 1:1986/DIN338.

Series S100

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Second Tap Metric Coarse Straight Flute Ground Thread HSS

The Sherwood second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before a fully threaded diameter is reached. If threading a blind hole a Plug tap will be required to cut threads to the bottom of the hole.

Sherwood Drills Taper Shank HSS

Suitable for single and multi-spindle drilling machines. The taper shank being the engineering industries recognised standard and most widely used method for holding and driving cutting tools. Manufactured to BS328;Part 1:1986, DIN345RN, DIN343RN.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT3) - Inch

Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Inch