Sherwood Hand Reamers

Sherwood Taper Pin hand reamers are used to produce a close tolerance surface finish in taper holes to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured to BS 328 : Part 4 : 1990 and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Taper Pin Hand Reamers - Inch

Sherwood 2 Flute Ball Nose Slot Drills Threaded Shank HSS

Used for diesinking, slot milling and profile milling. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Long Series Type B230T - Metric

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

45° Corner Angle - Metric (Form C)

For all dimensional and technical specifications please refer to our catalogue.

HSS-Co 8% Plain Shank Milling Cutters 2 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish.
Flute type: 30° Helix. Overall dimensions to DIN 844. Plain shank to DIN 1835A.

Regular Length

Sherwood HSS Plain Shank Corner Rounding Cutters

Designed to produce convex corner radii. For milling structural, carburising and heat treated steel up to 900N/mm2.
Manufactured to works standards.
5° RH Flutes.
Bright finish, straight helix.
Radii tolerance: ± 0.005”.

Metric

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Long Series Type 5331T - Inch

For all dimensional and technical specifications please refer to our catalogue.

3 Flute Straight Shank Countersinks

Sherwood countersinks are a chatter-free cutter that produce an excellent burr-free finish it is capable of deburring and countersinking in one stroke with no "back-off" of tool.
Countersinking a hole leaves an angled conical, chamfered recess on the finished job, for a tapered head bolt or screw to seat correctly into this angled form. Countersink bits can be used for deburring holes as well.
It will also countersink aluminium with no secondary bulge.
Ideal for special applications and exotic materials, a choice of hard coatings is available.

For all dimensional specifications please refer to our catalogue.

90 Degrees

Sherwood® Milling Cutters Plain Shank Carbide Micrograin

For optimum performance and maximum swarf removal when plunging, slotting and routing in light alloys, brass, aluminium, non-ferrous and other soft materials. Manufactured to USCTi Standards. Available in 2 flute for maximum swarf clearance, 4 flute for maximum rigidity and 3 flute offers a combination of the advantages achieved with 2 and 4.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute End Mills

Sherwood Machine Reamers

Sherwood machine reamers are used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. Manufactured from HSS with a 45 bevelled head.

Conform to BS 122 : Part 2 and BS 328 Part 4.

For all technical and dimensional specifications please refer to our catalogue.

Machine Reamers Taper Shank HSS - Metric

Sherwood Multi Flute End Mills Threaded Shank HSS

Used for profile milling and producing slots. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series E410T - Inch