Sherwood T-Slot Cutters Threaded Shank HSS

Used for machining T-slots on slide tables, fixtures etc., to DIN 650. For milling structural, carburized and heat treated steel up to 900N/mm2. Sizes up to 16mm and 1/2" have 6 flutes and 18mm and 5/8" upwards have 8 flutes. Made to DIN 851. Shank to DIN 1835/D. Flute form 12 RH/LH.

For all dimensional specifications please refer to our catalogue.

Metric sizes

Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Inch

Sherwood Multi Flute End Mills Threaded Shank HSS

Used for profile milling and producing slots. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series E410T - Inch

Sherwood Machine Reamers

Sherwood extra length machine reamers are used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size to allow the fitting of hardened and ground taper pins in the building of jigs, fixtures and dies.

Manufactured from HSS with a 45 bevelled head.

Conform to BS 328 : Part 4 : and DIN 9A.

For all technical and dimensional specifications please refer to our catalogue.

Machine Reamers Extra Length Taper Shank HSS - Metric

Sherwood Straight Shank Parallel Hand Reamers

Used to produce a close tolerance surface finish by hand in almost any environment i.e. on site or in a workshop. Manufactured to BS 328 : Part 4 : 1990 and DIN 206B.

Spiral Flute Parallel Hand Reamers - Inch

For all dimensional specifications please refer to our catalogue.

Sherwood Multi Flute End Mills Threaded Shank HSS-Co

Used for profile milling and producing open slots. Bright finish. Flute Type: 30° Helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series Type E411T - Metric

Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Inch

Sherwood Solid Counterbore HSS-E

Used for milling of pre-drilled holes to allow bolt or cap head screws to lie flush with the component surface. Spiral, 3 flute. Medium duty. Manufactured to BS328:5:1983.

For all dimensional specifications please refer to our catalogue.

Spiral 3 Flute Plain Shank

Sherwood 2 Flute Slot Drills Threaded Shank HSS-Co 5%

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

Short Series - Metric

Sherwood 4 Flute Ball Nosed End Mills Plain Shank Solid Carbide Micrograin

For maximum strength when milling harder materials where rapid swarf removal is not needed. 4 flute milling cutters have one of the strongest tooth structures available in solid cutters. Centre cutting as standard. Manufactured to ANSI Standards.

For all dimensional and technical specifications please refer to our catalogue.

Regular Series 4 Flute Ball Nosed End Mills