SMC One-Touch Fitting Male Connectors

KQH
Most common style used to pipe from female thread in the same direction.
KQH04-01S: Tube O.D. 4mm. Thread: R1/8.
KQH04-M5: Tube O.D. 4mm. Thread: M5 X 0.8..
KQH08-01S: Tube O.D. 8mm. Thread: R1/8.
KQH08-02S: Tube O.D. 8mm. Thread: R1/4.

Camozzi Swivel Run Tees

S6440
Super-rapid fittings for plastic tubes. Push-in fitting swivel run Tee.
Available in:
10mm tube - G1/4 thread.
10mm tube - G3/8 thread.
12mm tube - G3/8 thread.

Rexroth Bulkhead Plug Connector

QR1-RSC Series
Push-in fitting plastic bulkhead plug connector.
Available in diameters: 6, 8, 10 and 12mm.

Ambient temperature min/max: +0°C/+60°C.
Working pressure min/max: -0.95 bar/10 bar.
Materials:
Housing: Polybutyleneterephthalate.
Seal: Acrylonitrile Butadiene Rubber.
Tooth lock washer: Stainless steel.
Release ring: Polyoxymethylene.
Release ring holder: Die cast zinc; Brass nickel-plated.

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

QR1-RTK Series T-Plug Connector Pneumatic Fitting

Standard Metric M5-G T-Plug Connector push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM' and PKM' fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Pipe Inserts

Available in 10mm, 15mm and 22mm.

Series 2013

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Female - Female Elbows

Brass Straight Adaptors

Suitable for central heating systems This fitting is made of the following components:- The body is produced in brass ?O?Rings are nitrile rubber The collet is produced in acetal copolymer with stainless steel teeth.

SMC Rotary One-touch Fitting Male Elbow Adaptors

KSL (Standard)
KSL06-01S: Tube O.D. 6mm. RPM: 500. Thread: R1/8.
KSL08-01S: Tube O.D. 8mm. RPM: 400. Thread: R1/8.
KSL08-02S: Tube O.D. 8mm. RPM: 400. Thread: R1/4.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Elbow Connector

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Connector to Male Taper