Series 2043

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Female Y Connector

Camozzi Distribution Blocks

Series 2000 pipe fittings BSP adaptor 4-way anodised aluminium distribution block.
Available in threads:
G1/8 overall length 25mm.
G1/4 overall length 32mm.
G3/8 overall length 40mm.
G1/2 overall length 50mm.

Series 2530

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Male - Female Reducers

Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Bent Tap Connector

With brass swivel nut and sealing washer.
Suitable for central heating systems.

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

2020 Series

Series 2003

When involved in factory maintenance or plant installation it is often difficult to be certain which size of fitting will be required. The Camozzi pipe fitting range provides a cost effective solution to this problem. The full range includes straight, L - T shaped and cross piece male or female couplings, all of which are available in a large variety of thread sizes.

General Data:
Material: OT58 (nickel-plated).
Threads: GAS conical ISO 7 (BSPT). GAS cylindrical ISO 228 (BSP).
Pressure: 40 bar.
Fluid: compressed air or other low pressure fluids.
Temperature: -40C to 120C.



Equal Female Tees

Camozzi Female/Female Couplers

2543
Series 2000 pipe fittings BSP adaptor female adapter.
Available in G1/8, G1/4, G3/8 and G1/2 threads.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Tube suitability: Nylon, polyurethane.

Quick Exhaust Valve Female to Female

Pressure Range: 0.3 to 10 bar. Temperature Range: -18°C to +70°C.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless steel retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Type 1 Conical Silencer Sintered

Kobe? Tailpieces & Threaded Connectors

A comprehensive range designed for use in conjunction with airline couplings in garage and industrial applications. Case hardened with zinc finish.

Male Threaded Tailpieces

For connecting a hose to a female threaded fitting.