Push-fit Solution for Plumbing & Heating Systems

For use with mains fed and indirect cold water systems, vented and unvented hot water systems, vented and sealed central heating systems. Pipes Speedfit fittings can be used with copper pipe to BS EN 1057 and Speedfit cross-linked polyethylene (PEX) Barrier Pipe to BS7291. NOT to be used with gas, fuel oil or compressed air applications. Speedfit fittings cannot be used on stainless steel pipe. Standard Speedfit products are designed and manufactured under a fully integrated system assessed by B.S.I. to BS EN ISO9001. They are approved by the Water Regulations Advisory Scheme and BBA. Speedfit PEM? and PKM? fittings and Speedfit barrier pipe are kitemarked to BS7291 Part 1 and 3, Class S. (Licence No. KM39767). Pipe in ceilings and roof voids should be clipped every metre and should not be fitted any closer than 60mm from the end of the fitting. Pipe should be adequately supported by pipe clips to prevent undue stress (side load) on fittings. Can only be used with water or oil based paint, not cellulose based paints, paint thinners or strippers, solder flux or acid-based descalents or aggressive household cleaning products. Speedfit products, when used indoors, are not affected by sunlight. When used outdoors protect from ultra violet light by lagging or painting. It is recommended that all installations are checked prior to use to determine that a seal has been made.
Working temperatures and pressures: Central Heating: 3.0 bar at 92C. Hot Water: 6.0 bar at 65C. Cold Water: 12.0 bar at 20C.

Straight Tap Connectors

With brass swivel nut and sealing washer. Suitable for central heating systems.

Camozzi Swivel Branch Tees

S6430
Super-rapid fittings for plastic tubes. Push-in fitting swivel branch Tee.
Available in:
10mm tube - G1/4 thread.
10mm tube - G3/8 thread.
12mm tube - G1/4 thread.
12mm tube - G3/8 thread.
12mm tube - G1/2 thread.

Series S6440

Micro Super-Rapid fittings allow fast connection and disconnection of plastic tube, it can be repeated several times and can be performed using one hand and without the use of tools. The sealing ring (O-Ring) can be easily replaced if it is damaged or should the rubber compound from which it is made wear with time. This advantage derives from the simple execution of the internal collet, which can be extracted allowing the replacement of the O-Ring.

General data:
Material body and collet: brass OT nickel-plated O-Ring NBR, seal PTFE, NBR, PA
Threads: M3, M5, M7, G1/8, G1/4.
Pressure: min. -0,8 to max. 16 bar (see tubing).
Tube to connect rilsan: PA 6 - 11 - 12 , polyethylene, polyurethane.
Diameters: 3, 4, 6, 8 and 10mm.
Fluid: compressed air (for other types of fluid, contact our engineers).
Temperature: -10C to 60C (see data for tubing used).



Swivel Run Tees

Camozzi Extended Swivel Elbows

7526
Super-rapid contact fitting Technopolymer extended swivel elbows with O-ring assembled.
Available in:
4mm tube, G1/8 thread.
6mm tube, G1/8 thread.
6mm tube, G1/4 thread.
8mm tube, G1/8 thread.
8mm tube, G1/4 thread.

Elbow Type

AS series in line speed controllers minimise installation time and cost as they reduce the mounting height and enable compact machinery design. The number of needle rotations has been increased from 8 to 10 turns to permit easy control at low speeds. Applicable tube material nylon, soft nylon and polyurethane tubing.
Operating pressure: 1MPa max.

PCL? InstantAir Airline Adaptor

The InstantAir range of couplings and adaptors are the original and genuine Broomwade bayonet fittings. Suitable for most fixed compressed air applications, although swivel adaptors are recommended for hose applications. Steel bayonet type couplings, preventing accidental disconnection.
Nominal bore: 5.6mm.
Maximum flow rate: 54cfm 100 lbf/in.
Maximum working pressure: 17 bar (250 lbf/in).
Temperature range: -20C to 80C.



1/4" BSPT.

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Blanking Plug

Quick Fit Pneumatic Fittings

Suitable for vacuum application. Rapid type push on fittings with retaining nut.

Threaded Adaptors

5010 Series

Kennedy® Pneumatic Fittings

Quick and simple tube insertion, compact lightweight design, advanced well proven tube retaining system, re-usable thread seal. Main body manufactured from Nickel plated brass, acetal resin, PBT with a stainless stell retaining ring, nitrile tube seal and acetal resin tube release collar. Pressure range: - 0.9 bar min to 10 bar max. Temp range: -20°C min to +70°C max. Tube suitability: nylon, polyurethane.

Bulkhead to Female Parallel

Bosch Rexroth Pneumatic Fittings

Rexroth QR1 Series push in pneumatic fittings type are available for inch tubing/NPT threads and metric tubing/ISO-G (BSPP) threads. The user friendly oval release ring allow the push-in fittings to quickly release from the tubing much more easily than traditional round release rings. QR1 fittings come in standard and mini sizes, plus function fittings such as ball valves, check valves, flow control etc. They feature premium materials such as the stainless steel tube locking mechanism and polymer body and release ring.

QR1-RVL Series Long Elbow Pneumatic Fitting

Standard metric M5-G 1/2 Long Elbow push fit pneumatic fitting for compressed air hoses: 4 to 16mm diameter.

For further specification on this product please see the attached PDF under the additional information tab.