SK High Power Wedge Belts

To ISO 4184, BS 3790, DIN 7753 and
USA Standard RMA/MPTA.
The wrapped Optibelt SK wedge belt has been developed with mechanical engineering in mind.
It transmits substantially more power than the classical V-belt with comparable top width.
The Optibelt SK high performance wedge belt is preferred for use in heavy mechanical engineering with very high load requirements, which can be over 2000kW.
*Belts marked are part of the S = C PLUS range with an efficiency of approximately 97% and are suitable for use and require no service or adjustment during service life.

Belt Section 22/C (SPC/22)

RexPro Carbon Steel Chain

With RexPro, Rexnord set a new standard for quality chains. The RexPro chain is the result of further developing the
Rexnord high performance chain. Over a timespan of four years the combination of selected steels, optimised manufacturing and the RexPro lubrication have all achieved these outstanding product characteristics.

American Standard Roller Chain - DIN8188/ISO 606 (ANSI B29.1).

Triplex Chain

W22 3 Phase Motors - A Revolution in Energy Efficiency

The W22 is a range of three-phase induction motors which reduces energy consumption, noise, vibration and cost of ownership.With an aerodynamic frame, redesigned cooling system, unique WISE insulation system and new WSeal 'V' Ring with double lip and metallic cap, the W22 range of motors is quieter, more reliable, easier to maintain and more cost effective.

Cast Iron IE3 Multi-Voltage Three Phase Motors

Cast iron frame motors - IE3 (Premium Efficiency) three-phase motors. These motors exceed the IE3 New European Minimum Energy Performance Standard (EU MEPS). Thermisters fitted as standard in frame 160 and above. IP55 protection as standard (up to IP66 on request).

RexPro Carbon Steel Chain

With RexPro, Rexnord set a new standard for quality chains. The RexPro chain is the result of further developing the
Rexnord high performance chain. Over a timespan of four years the combination of selected steels, optimised manufacturing and the RexPro lubrication have all achieved these outstanding product characteristics.

Triplex Connecting Links

RexPro Carbon Steel Chain

With RexPro, Rexnord set a new standard for quality chains. The RexPro chain is the result of further developing the
Rexnord high performance chain. Over a timespan of four years the combination of selected steels, optimised manufacturing and the RexPro lubrication have all achieved these outstanding product characteristics.

Duplex Connecting Links

Adapter Sleeves

Adaptor sleeves are commonly used for locating tapererd bored bearing and securing them to a shaft. They can be accurately positioned and dismounted. By using in conjuction with SNR feeler gauges accurate radial clearances will be achieved.

SNR Shaft Seals & Adaptors

Cover plates are made of corrosion-resistant steel and used where the shaft terminates inside the housing. In this configuration only one seal set will be required.

Cover Plates

Deep Groove Ball Bearings - C3 Clearance

C3 bearings have an additional internal radial clearance to cope with high speed environments where excess heat is generated.

Rubber sealed type:

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

SNR Bearings

SNR double-row ball bearings have become the natural substitute for single-row ball bearings for higher radial load applications, or for axial loads in both directions. Suitable for mean rotating speeds, these bearings only admit very slight misalignment between shaft and housing, to the order of 0.06.
Standard synthetic material cage.

Applications: electrical motors, household appliances, wood-machine spindles, small reduction gears.

4300 Series Double Row Radial Contact Ball Bearings

Aluminium Motors 2P

Aluminium Frame Motors - IE2 (Eff1 Premium Efficiency).
Suitable for inverter duty applications.
Thermistors (1 per phase), fitted in frame 132M and above.

Aluminium - B3 - Foot Mounted - 2 Pole - 3,000rpm - AC 3 Phase