Taper Roller Bearings

Tapered roller bearings are comprised of solid inner and outer rings with raceways, taper rollers and cages manufactured from pressed steel. The bearings are not self-retaining. As a result, the inner ring with the rollers can be fitted separately from the outer ring. Tapered roller bearings are not sealed and not supplied grease filled.

Gilkes Submersible Pumps

Submersible pumps for drainage, de-watering and general transfer of both clean and dirty liquids. AISI304 stainless steel housing and impeller. 230V 50Hz single phase.
Motors are 0.25 to 2.25kW and are all IP68.
Max. liquid temperature 40°C.
Max immersion
depth 5m.
Solid size: 7 - 20mm.
Power cable length minimum 5m.
Available with or without the float switch.
Applications:
• Emptying of sump pits, rainwater tanks.
• Irrigation
• Emergency removal of flood waters in basements
• Transfer duties for clear, sandy and muddy liquids
• Residential and industrial waste water pumping
• Sewage treatment and disposal
• Industrial effluent plants


Image for illustration
purposes only.

Titan 2GL Submersible Pump in Cast Iron

Super X-Power V-Belt

Moulded Cogged Raw Edge Wedge Belts



Belt Section 13/A (SPA/13)

Cast Iron Motors - 2P

Cast Iron Frame Motors - IE2 (Eff1 Premium Efficiency). Suitable for inverter duty applications. Regreasing nipple from frame 225S/M and above. Thermistors (1 per phase) fitted in
frame 160M and above.

Cast Iron - B5 - Flange Mounted - 2 Pole - 3,000rpm - AC 3 Phase

Thrust Ball Bearings

Thrust Bearings are designed primarily to support axial loads at contact angles between 30° and 90°. Just as with radial bearings, these bearings differ according to the type of rolling element they use. With thrust bearings, it is necessary to supply an axial preload in order to prevent slipping movement between the bearing's rolling element and raceways.
Comprising of caged ball bearing element and pair of shaft housing washers (bearing shaft washer and housing washer, and the normal contact angle is 90°. Axial loads can be supported in only one direction, radial loads cannot be accommodated. Spherical roller and needle roller versions are also available.

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 10/Z (SPZ/10)

Max Width (b1) 10mm, Height (h)6mm.

Conti-V Standard Multiflex V-Belts

Classical section wrapped V-belts to DIN 2215. Moderately oil-resistant. Resistant to temperatures from -55C to +70C. Electrically conductive (anti-static) to ISO 813. Insensitive to dust. Suitable for tropical climates.

Belt Section 13/A (SPA/13)

Max Width (b1) 13mm, Height (h)8mm.

Single Row Deep Groove Ball Bearings - C3 Internal Clearance

C3 Bearings have an internal clearance to cope with high speed environments where excess heat is generated.

Rubber Sealed Type

With rubber seals inserted into the outer raceway and in contact with the inner race providing protection against the ingress of moisture, dust and other foreign objects. The seals also retain the pre-filled grease in the bearing. Seals can be easily removed for applications that only require one seal.

Grade G100 Steel Balls

Low carbon case hardened steel balls are for general use in castors, conveyors, non precision bearings and any slow rotating parts.They have resistance to shock loads with a good load carrying ability and excellent resistance to surface wear. The G100 standard ball is of a high spherical standard.

Inch

Tab Washers

Tab washers are used for securing KM series lock nuts. They have an inner tab for location on the adaptor sleeve. One of the external tabs is bent over a slot when used wit the
KM series lock nuts.