574 Flange Sealant

General purpose flange sealant for gaps up to 0.5mm. Typical applications are hydraulic and pneumatic control valves, transmission and engine flanges and marine pipework. Suitable for 90% of flange sealing applications. Carries the German DVGW approval. Test in accordance with EN751-1. certified to NSF P1.

574 - General Purpose Flange Sealant

Conforms with BS6920 (potable water). General purpose flange sealant for gaps up to 0.5mm. Typical applications are hydraulic and pneumatic control valves, transmission and engine flanges and marine pipework.
Suitable for 90% of flange sealing applications.

577 - Thread Sealant

Medium strength. Suitable for copper, mild steel, cast iron, stainless steel and galvanised pipe. Carries the German DVGW approval. tested in accordance with EN751-1. Certified to NSF P1. Conforms with: BS 6956 : 7 (gas).
AGA Approval No. 3207 to 1050kPa (152psi).

542 Hydraulic Sealant

Medium strength, medium viscosity. Impervious to all common hydraulic fluids including fire resistant synthetics. Will not clog valves or fine filters. Replaces tapes, pastes and self-sealing compression joints.
Recommended for threaded fittings as used in hydraulic and pneumatic installations.
Medium threadlocking strength.
Suitable for high pressure systems.
Temperature range: -55C to 150C

Wellseal Jointing Compound

Gives the best possible sealing performance in the most varied of conditions. Threaded connections, flat faced joints, with or without a gasket depending on assembly design. Resistant to commonly used fuels, lubricants and coolants, is non-corrosive and free from abrasive fillers.

542 Hydraulic Sealant

Medium strength, medium viscosity. Impervious to all common hydraulic fluids including fire resistant synthetics. Will not clog valves or fine filters. Replaces tapes, pastes and self-sealing compression joints.
Recommended for threaded fittings as used in hydraulic and pneumatic installations.
Medium threadlocking strength.
Suitable for high pressure systems.
Temperature range: -55C to 150C

Hylomar Universal Blue Gasket & Sealing Compound

Leading non-setting gasket and sealing compound in use world-wide. Used some of the world's major automotive manufacturers and several Formula 1 teams. Non-hardening and non-setting allows for unlimited assembly time. Vibration resistant. Allows metal to metal contact. Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants. Seals surface imperfections. Withstands rapid variations in temperature. Flame, dust and moisture proofing properties.

Available in 40g, 100g and 350g.

518 - Flexible Fast Cure Gasket

Recommended for sealing aluminium flanges and fills up to 0.5mm. Withstands fluctuations in pressure, temperature and vibration. Replaces pre-cut gaskets on rigid parts.

515 Gasket Eliminator

Flexes with minor flange movement. Fills gaps up to 0.25mm. Does not shrink or migrate. Temperature range -55C to 150C. AGA approved No. 2590 up to 6900kPA (100psi).

6300 High Strength Retaining Compound

LOCTITE® 6300™ is designed for the bonding of cylindrical fitting parts. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. Typical applications include holding gears and sprockets onto gearbox shafts and rotors on electric motor shafts.



Technical Data:
• Diametrical clearance: Up to 0.15mm
• Service temperature range: -55°C to + 175°C
• Tensile shear strength: 20 N/mm²
• Fixture time on steel: 10 min.
• Pack size: 50ml

Benefits:
• Leading in Health & Safety
• No hazard symbols, no risk phrases & no safety phrases
• oeWhite” Material Safety Data Sheet ?? no entries in sections
2, 3, 15 and 16 of MSDS acc. to (EC) No. 1907/2006 ?? ISO
11014-1 Good thermal resistance