High Speed Steel Knurls

Precision hobbed to produce burr-free clean cut knurls.

Left Hand

Bott Louvre Panel Racks

All models 1000mm wide x 550mm deep. Double or single sided versions. Complete with bin kits. Epoxy powder coat finish. Optional base tray available for all models.

1775mm High Static Rack - Double Sided

16917202.11V
Fittings: 80 piece hook kit.

Precision Ground Flat Stock (1000mm)

The dimensional stability of ground flat stock combines with other useful characteristics including excellent resistance to cracking during heat treatment compared with other, more highly alloyed, cold work tools. Relatively soft and easy to machine. High wear resistance after heat treatment. Holds a good cutting edge. Suitable for EDM machining.
Typical applications: widely used in precision tools, machine knives, gauges, jigs, templates, punches, dies and machine parts.
The Cost Cutting Stock: extensive range of widths and thicknesses enables the selection of an appropriate size of ground flat stock to minimise material and machining costs.

Manufactured from BS4659 B01 grade steel equivalent to AISI 01 and Werk. No. 1.2510.
Chemical analysis range:
Carbon 0.90 - 1.00%
Silicon 0.40%
Manganese 1.00 - 1.20%
Chromium 0.50 - 0.70%
Tungsten 0.50 - 0.70%
Vanadium 0.05 - 0.25%

Chemical analysis typical:
Carbon 0.95%
Silicon 0.40%
Manganese 1.20%
Chromium 0.55%
Tungsten 0.55%
Vanadium 0.15%

Metric sizes

Tolerances:
Thickness: -0.00mm/+0.050mm.
Width: -0.00mm/+0.200mm.
Length: -0.00mm/+5.000mm.

Steel Locker

Hat shelf and 2 x coat hooks fitted in the single door locker (450mm deep locker also has a hanging rail), 2 x coat hooks fitted in each compartment of the 2-tier locker. BSI Quality Assured (meet the requirements of British Standard for Clothes Lockers BS4680:1996 ?Standard Duty?).

Picture for illustration only not accurate for colour.

Fixture Components

Material: Medium Carbon Steel. Surface Finish: Manganese Phosphate.

FC40 - T-Slot Bolt

Precision Ground Flat Stock (500mm)

The dimensional stability of ground flat stock combines with other useful characteristics including excellent resistance to cracking during heat treatment compared with other, more highly alloyed, cold work tools. Relatively soft and easy to machine. High wear resistance after heat treatment. Holds a good cutting edge. Suitable for EDM machining.
Typical applications: widely used in precision tools, machine knives, gauges, jigs, templates, punches, dies and machine parts.
The Cost Cutting Stock: extensive range of widths and thicknesses enables the selection of an appropriate size of ground flat stock to minimise material and machining costs.

Manufactured from BS4659 B01 grade steel equivalent to AISI 01 and Werk. No. 1.2510.
Chemical analysis range:
Carbon 0.90 - 1.00%
Silicon 0.40%
Manganese 1.00 - 1.20%
Chromium 0.50 - 0.70%
Tungsten 0.50 - 0.70%
Vanadium 0.05 - 0.25%

Chemical analysis typical:
Carbon 0.95%
Silicon 0.40%
Manganese 1.20%
Chromium 0.55%
Tungsten 0.55%
Vanadium 0.15%

Metric sizes

Tolerances:
Thickness: -0.00mm/+0.050mm.
Width: -0.00mm/+0.200mm.
Length: -0.00mm/+5.000mm.

Vertical Industrial Toggle Clamps

Designed to improve performance in fabrication and engineering clamping applications. The rapid clamping/unclamping made possible by the use of toggle clamps can greatly reduce machine/operator 'down-time' during all stages of production. Clamping Capacity - the forces stated are the maximum loads that can be applied without causing permanent deformation. Due to leverage ratios, the holding capacity will be greatest at the point on the bar nearest to the handle of the clamp and forces stated have been achieved at this point.

'U' Bar (Adjustable) Type

Straight Base

Indexa Die Springs

The heat and surface treatment plus the high quality of steel used in the manufacturing process ensure the springs will bear a high number of stresses without breaking or without appreciable loss of load. Every batch of springs is subject to a rigorous testing procedure to ensure that a consistent quality is maintained. Longer springs should be guided along their course.

Light Load Springs Colour-Coded Green

Matlock™ Parts, Component and Tool Storage Bins

Matlock™ high strength Polypropylene storage bins are designed to solve your storage problems, they are suitable for small to large component or part storage. The versatile Matlock™ storage bin can be interlocked side by side, nested on top of each other, hung on steel louvred panel (supplied separately) or using riser rods (supplied separately) they can be stacked on top of each another, this functionality allows you to create the storage system to satisfy your specific requirement.

Matlock™ storage bins are available in seven sizes and a choice of four colours blue, green, red and yellow and can be fitted with label holders (supplied separately).

For all dimensional specifications and accessories please refer to our catalogue.

Plastic Storage Bins

Matlock™ Plastic Storage Bin Size: No.3 Dimensions 278x222x165mm(LxWxH)

Matlock Shelving and Racking

Matlock Euro shelving is available in a range of sizes and configurations to meet your specific storage requirement. The heavy duty all steel shelving system has a 200Kg UDL* per shelf capacity making it ideal for industrial storage.

Features include:
The shelving bays are available with solid cladding or open/braced backs and sides. Shelve height is adjustable and are fitted on clips for easy repositioning.
High quality, light grey powder coat finish.
Biocote antimicrobial protection reduces levels of bacteria on surfaces by up to 99.99% .
Up to 200Kg UDL* capacity per shelf.
Self Assembly tools required.

Please refer to the catalogue PDF for all dimensional information.

*Uniformly Distributed Load

Open Bay Euro Shelving