Ajax Machine Tools

Ajax hydraulic power hacksaw machines are manufactured from a solid cast iron construction and a practical design. The machine vice swivels to allow angular cutting, the bow has infinitely variable cutting feed with automatic cut off at end of cut with rapid bow return.

The machine is complete with blade, length setting gauge, re-circulating coolant system, swarf collection tray, bar end support, bundle cutting and roller stand, fully CE marked.

Hydraulic Power Hacksaw

Model Number: AJPH280
Supply: 400V/3ph 50Hz.
Motor rating: 2hp.
Maximum cut diameter @90: 280mm.
Maximum cut diameter @45: 130mm.
Maximum cut rectangular @90: 250 x 250mm.
Blade speed: 80/100/120SPM.
Blade size: 450 x 32 x 1.6mm.
Weight: 520kg.

Model D420 x 1500 420mm Swing x 1500mmDBC 3ph 0340-1165

Induction hardened and precision ground heavily ribbed prismatic bed. Substructure and lathe bed made from a single block of Meehanite cast iron. Camlock spindle nose D1-6. Oil-quenched hardened work spindle bedded in two readjustable precision taper roller bearings. Guaranteed concentricity precision of the spindle nose 0.015mm. Smooth running work spindle gearwheels hardened and precision ground. Leadscrew and feed shaft drive easily switchable via oil quenched feed gear. Adjustable safety coupling of the feed shaft. The tailstock may be shifted plus/minus for taper turning. Right - left - hand rotation can be switched with the help of the indexing spindle. Emergency stop mushroom switch, lockable main switch. Removable gap bed. Adjustable dial of the threading gauge. Mechanical foot spindle brake. Manufactured to DIN 8606 (toolmakers precision).

Standard accessories:
200mm 3 jaw chuck, 250mm 4 jaw chuck, 350mm face plate, steady rest, follow rest, coolant system, rear splash guard, spindle brake, 2-step drive motor, electrically interlocked chuck guard, turret limit stop with fine adjustment acting as end stop on lathe saddle, machine lamp, threading gauge, operating tools.

Specifications:
Between centres: 1500mm.
Centre height: 210mm.
Max.turning diameter: 420mm.
Max turning diameter over saddle: 255mm.
Max turning diameter over gap: 590mm.
Bed width: 250mm.
Spindle hole: 52mm.
Spindle taper: 6MT.
Tailstock taper: 4MT.
Spindle: D1-6.
No of spindle speeds: 16.
Spindle speeds: 45-1800rpm.
Longitudinal feeds: 0.05-1.7mm/rev.
Cross feeds: 0.025-0.85mm/rev.
Pitch metric (39): 0.2-14mm.
Pitch inch (45): 2-72 TPI
Modular thread (18): 0.3-3.5 MP
Trapezoid thread (21): 8-44 DP.
Top slide travel: 140mm.
Cross slide travel: 230mm.
Sleeve travel: 120mm.
Max. Tool shank: 20mm.
Main motor power: 4.5kW.
Coolant pump: 0.1kW.
Size (LxWxH): 245x91x135cms.
Weight: 1950kg.

SIP® Trade 16" Variable Speed Scroll Saw

01928
Parallel arm design perfect for cutting intricate curves while keeping an accurate 90º edge. Robust rounded edge, cast iron table can be tilted 45º left and right. Flexible dust blower for fast and easy clearing of saw dust. Integrated light, laser guidance, adjustable safety guards - safe and unhindered cutting.

Specifications:
Supply: 230v (13amp).
Motor: 120w.
Cutting stroke: 15mm.
Cutting speeds: 400-1600 stroke/min.
Weight: 17kg.
2 year warranty.

Ajax Machine Tools

Ajax hydraulic power hacksaw machines are manufactured from a solid cast iron construction and a practical design. The machine vice swivels to allow angular cutting, the bow has infinitely variable cutting feed with automatic cut off at end of cut with rapid bow return.

The machine is complete with blade, length setting gauge, re-circulating coolant system, swarf collection tray, bar end support, bundle cutting and roller stand, fully CE marked.

Hydraulic Power Hacksaw

Model Number: AJPH450
Supply: 400V/3ph 50Hz.
Motor rating: 3hp.
Maximum cut diameter @90: 450mm.
Maximum cut diameter @45: 160mm.
Maximum cut rectangular @90: 400 x 430mm.
Blade speed: 80/100/120SPM.
Blade size: 650 x 50 x 2mm.
Weight: 760kg.

SIP 410mm (16") Professional Heavy-Duty Bandsaw

01445
Specifications:
Powerful 3HP motor 230V, 2.2kW.
Throat width: 410mm.
Large tilting table: 10-45.
Table size: 535 x 435mm.
Table height: 900mm.
Table width: 6-37mm.
Table length: 3345mm.
Saw blade speed: 7 or 14m/sec.
Supplied with blade: 3345 x 12mm x 6TPI.
Max cutting depth: 254mm.
Supplied with floor stand.
Two year warranty.
Weight: 126kg.

Heavy-Duty Vertical Bandsaws

Heavy-Duty suitable for continuous use. High quality electrics and limit switches to blade wheelcovers make safe to use and conform to CE. Air pipe keeps the visibility clear near the cutting edge

Standard Accessories:
Saw blade butt welder with integrated annealing unit.
Blade shear, grinder & built-in blade and tyre cleaning brush.
Lo-volt light.
Set of tools.
Instruction manual and parts list.
Rip fence for straight, repeated cutting and is easily adjustable for varied size.
Mitre protractor for angular cutting.

Model KV100 100? Throat 1-631-400

Cutting blade to column: 1000mm.
Capacity max. work height: 300mm.
Table size: 600x500mm.
Table extension: 450x500mm.
Table inclination (4 ways): 15.
Blade length: 4540mm.
Max width: 16mm.
Blade speeds stepless: Low 15-55m/min, High 96-390m/min.
Butt welder capacity: 2.4KVA 3-16mm.
Drive motor: 1.5kW.
Weight: 800kgs.

Model D330x1000, 0340-1007 3ph, 0340-1006 1ph

Rigid heavily ribbed, hardened and precision ground cast iron bed with V guideways. Camlock spindle nose D1-4. Hardened oil running headstock spindle with high precision, realignable tapered bearings. Guaranteed spindle nose runout less than 0.015mm. Closed quick action feed and screw cutting gears running in oil bath. Simultaneous engagement of lead screw & power feed levers is prevented by interlocking. Adjustable slip clutch of lead screw. Forward/reverse spindle switch. Safety switch with no-volt release, emergency stop and motor protection. Foot brake. Gap bed. Manufactured to DIN 8606 (Toolmakers Precision).

Specifications:
Centre height: 165mm.
Max swing over bed: 330mm.
Max swing over saddle: 198mm.
Max swing in gap: 476mm.
Length of gap: 115mm.
Distance between centres: 1000mm.
Width of bed: 187mm.
Spindle bore: 38mm.
Spindle nose: D1-4.
Spindle taper: MT 5.
Tailstock taper: MT 3.
No of spindle speeds: 8.
Range of spindle speeds: 70?2000rpm.
Leadscrew dia/pitch: 22mm, 3mm.
Cross feed: 0.033 ? 0.933mm/rev.
Longitudinal feed: 0.097 ? 2.713mm/rev.
Metric threads: 0.4 ? 7mm.
Imperial threads: 4 ? 56tpi.
Diametral threads: 8 ? 120dp.
Module threads: 0.2 ? 3.5mp.
Top slide travel: 85mm.
Cross slide travel: 170mm.
Motor power: 1.5kW.
Tool section: 16mm.
Size (LxWxH): 193 x 75 x 151cm.
Net weight: 600kg.

Ajax Machine Tools

The range of Ajax gear head pedestal mounted drilling machines are known for their high quality, robust design and manufactured in Europe.

The range starts at 25mm capacity up to the huge 70mm capacity machine, all gear driven heads fully immersed in oil are designed for heavy-duty and long life and total range has automatic drill ejection from spindle.

Push button control of forward/reverse spindle direction, emergency switch, interlocked drill guard, table rise and fall by rack and pinion movement, ease of speed change.

The machines have in-built low voltage lighting and are fully CE marked. 2 year warranty.

All machines from the AJ32 upwards are complete with automatic spindle feed which can be preset to a desired depth, coolant pump and piping.

Gear Head Pedestal Drill

Model No: AJ25
Drilling Capacity: 25mm
Spindle Taper: MT3
Spindle Travel: 120mm
Speed: 65-3060rpm
No. of Speeds: 8
No. of Feeds: Optional
Table Size: 380x400mm
Voltage: 400V 3pH 50Hz
Main Motor: 1.2kW
Weight: 260Kg

For all technical and dimensional specifications please refer to our catalogue.

Geared Drive Bandsaws

Convincing arguments: quality, efficiency and price. User-friendly safety switch according to IP54 with under voltage release and protective motor switch. Three blade speeds via gear shifting mechanism. Robust cast iron design. Lowering using hydraulic system with continuous adjustment. Coolant system supplied as standard. Ball bearing 5 point blade guide. Quick action vice. Automatic limit stop. Chip brush.

Standard Accessories:
Bi-metal blade.
Hydraulic counter pressure cylinder.
Machine sub structure.
Material limit stop.
Quick action vice.
Coolant equipment.

Models S181G: 0330-0176 240V 1PH / 0330-0182 415V 3PH

Specifications:
Maximum capacity details:
Cutting range at 0 (Round): 180mm.
Cutting range at 0 (Square): 180 x 240mm / 65 x 300mm.
Cutting range at 45 (Round): 110mm.
Cutting range at 45 (Square): 170 x 110mm.
Blade speed: 39/66/82 m/min.
Blade size: 2362 x 19mm.
Dimensions: 1275 x 450 x 1100mm.
Weight: 130kg.
Motor power: 750w.

Osaki™ Optional Accessories

A range of optional accessories to suit the Osaki? Mini Milling/Drilling Machine (OSA-271-5500K) are available.

For full details please refer to our catalogue.

3MT Direct Drive Collet Set