产品 / 切削工具
编号:GUH0660525A
●产品描述:
Guhring Machine Chucking Reamers Intermediate Diameter HSS-E
Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.
Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.
Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.
Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.
For all technical specifications please refer to our catalogue.
编号:GUH0250040N
●产品描述:
Guhring Jobber Drills Steam Tempered HSS
Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.
Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.
Series 205
编号:KDY0318860K
●产品描述:
Diemakers Riffler Files
Swiss Pattern. Available in a complete range of shapes the 15cm are used by diemakers, jewellers, silversmiths, engravers etc. All are double ended with the same cut both ends.
编号:SHR0252840E
●产品描述:
Sherwood Drills Taper Shank HSS
General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.
For all dimensional specifications please refer to our catalogue.
Series T100 (MT4) - Metric
编号:DOR0250366V
●产品描述:
Dormer Jobber Drills TiN Tipped
Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.
Series A002
编号:AME1551900Q
●产品描述:
Allied Maxcut Series 1 and 1.5 Holders
Diameter range: 17.53 to 24.38mm.
For all dimensional specifications please refer to our catalogue.
Flanged Straight Shank
编号:GUH0266556G
●产品描述:
Guhring Production Jobber Drills HSS-Co 5%
Rigid, high heat resistant drill with large helix angle of 35. Suited for titanium and titanium alloys, stainless steels and heat resisting austenitic steels. TiN coated gives greater wear resistance and longer tool life. Limited suitability for special alloys such as Hastelloy, Inconel, Nimonic etc. Manufactured to DIN338.
Series 657 - Metric
编号:SHR0250236Q
●产品描述:
Sherwood Jobber Drills Bright Finish HSS
General-purpose drills for steel, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle: 10-20, tolerance of diameter: h8, tolerance of shank: f11. Manufactured to BS328/DIN338RN. Bright finish: drills with a bright finish are supplied in the as-ground condition and such tools are used generally in the machining of non-ferrous materials.
Series J100 - Metric - Bright Finish
编号:AME1841032K
●产品描述:
Allied Maxcut Thread Mills
The MaxThread™ threadmill range is manufactured from solid carbide with ground helical flutes and a TiAlN coating as standard. These product have been designed for the low volume/low cost production environment, providing excellent performance at a competitive price. A helical flute design has been maintained across the MaxThread™ range to allow
for maximum production benefits and to negate the need for straight flute thread mills. A comprehensive range of thread forms and technical information further supports the programme.
Features and Benefits:
Helical flute which offers increased strength and rigidity when cutting forces are applied.
TiAlN coated for increased tool life over uncoated tools.
Extensive range of thread forms.
High quality for consistent predictable production.
Metric Thread Mills
Solid Carbide Threadmills Metric ISO TiAIN coated
编号:SNK1211332K
●产品描述:
Sandvik Threading Toolholders and Inserts
Sandvik's 266 CoroThread toolholders and inserts provide a high level of stability for threading applications in demanding industries, where precision is paramount.
266 CoroThread ISO Metric Internal Right Hand Threading Insert
Grade description for GC1125:
New PVD-TiAIN-based coating and substrate combine to improve wear resistance and security for threading, providing the option of running at higher cutting speeds or for a longer time in cut.