Dormer 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30 helix. Manufactured to BS 122: Part 4: 1980.
Material:
XS1 HSS powder metallurgy steel. This provides a finer and more consistent grain structure than HSCo resulting in a tougher product able to more easily withstand the shock load and intermittent cutting associated with milling operations. Tool life and wear resistance, exceeds standard HSS and is comparable to HSCo cutters. Superior edge strength and rigidity, resulting in improved surface finish and slot consistency equal to and in some cases better than HSCo. A productivity increase of around 40% over existing HSS cutters. Flute and overall lengths: to BS122/4.
Finish: bronze finish: provides a uniform structure and hardness at the tool surface, whilst also aiding tool identification.

For all dimensional and technical information please refer to our catalogue.

Short Series C191 - Metric

Sherwood Drill Blanks HSS

Jobber length blank hardened and ground all over. Accurately ground without back taper. Diameter Tolerance: h8. Manufactured to DIN 338.

Series J400

Sherwood 2 Flute Ball Nose Slot Drills Threaded Shank HSS

Used for diesinking, slot milling and profile milling. Bright finish. Flute type: 30° helix. Manufactured to BS 122 : Part 4 : 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series Type B210T - Metric

Sherwood Extra Length Drills Taper Shank HSS

General purpose drills for steels, cast steel, grey cast iron, malleable cast iron, nickel brass, aluminium, alloy and graphite. Point angle 118, helix angle: normal, web thickness: standard, relief angle 8-20, tolerance of diameter: h8. Point angle to BS328 PTI 1986.

For all dimensional specifications please refer to our catalogue.

1 Morse Taper - Metric

Dormer Stub Drills HSS TiN Tip Coated

Designed for increased productivity and tool life compared to standard stub drills. TiN coating has been applied to 35%-50% of the flute length (dependent on drill diameter) to keep cost down and lower the cost per hole. The 135 split point is advantageous for the pre-drilling of rivets and for drilling in sheet metal. Suitable for drilling alloy steel, carbon steels, cast iron, titanium and aluminium. Manufactured to DIN1897, ANSI.

Series A022 Stub Drill HSS TiN Tip Coated - Inch

Taylor & Jones Spiral Flute Bridge Reamers

Have a taper lead angle of 1 in 10 on diameter and are used for reaming pairs of holes which may be out of alignment, particularly with structural steel components, i.e. when assembling pre-drilled steel plate ready for riveting. Previously known as 'Boilermakers' reamers. Manufactured to BS 328 : Part 4 : 1990.

For all dimensional specifications please refer to our catalogue.

Spiral Flute Bridge Reamers - Metric

Sherwood Machine Reamers

Used to produce a close tolerance surface finish by enlarging pre-drilled holes to a finished size. 45 beveled lead. Manufactured to BS 122 : Part 2 and BS 328 Part 4.



Imperial Limits of Tolerance (to H7)\t Diameter \t \tOver\tUp to and Including\t High \t Low \t -\t7/64"\t0.0003\t0.0001\t7/64"\t15/64"\t0.0004\t0.0002\t15/64"\t25/64"\t0.0005\t0.0002\t25/64"\t43/64"\t0.0006\t0.0003\t43/64"\t11/8"\t0.0007\t0.0004\t11/8"\t11/2"\t0.0008\t0.0004\t11/2"\t2"\t0.0010\t0.0005

Sherwood Jobber Drills Steam Tempered HSS

Suitable for drilling steel, cast steel, alloyed and unalloyed, grey cast iron, spheroidal iron, sintered powder metal, German silver and graphite. Manufactured to BS328/DIN338RN.

Black Finish (W-Finish)
This is the most common surface finish and is the result of a steam tempering operation in which steam is passed over the product during a controlled tempering cycle, producing a black oxide layer. Black tools are generally recommended for ferrous applications where the oxide layer aids chip flow, helps to dissipate heat by retaining some coolant on the tool surface and also helps to prevent the tool from staining.

Series J100

A510 5.80mm HSS-TiN ADX S/S JOBBER DRILL

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Bar Turning Tools

Left Hand. Available in Grades P30 and K20.