Sherwood Long Series Drills Steam Tempered HSS

General-purpose drills to drill steels with tensile strength up to 1,000N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118, helix angle: normal, web thickness: normal, relief angle: 10-20, tolerance of diameter: h8, tolerance of f11. Manufactured to BS328;Part 1:1986, DIN340RN, ISO494.

For all dimensional specifications please refer to our catalogue.

Series L100 - Metric

Iscar Carbide Endmills

Iscar FINISHRED Solid Carbide Endmills.
2 Applications in 1 Solid Carbide Endmill:
The EFS.. B44 endmill features 4 flutes with a 45 helix,
two serrated flutes and two continuous flutes.
The tool is fully effective and enables running at rough machining
parameters, resulting in finish surface quality.
Unique tool design reduces vibration at high load applications.
The tool produces short and long chips simultaneously. This chip mixture is
evacuated more easily than each individual chip type, which is an excellent
solution for slotting and cavity milling applications.
One tool change and set up time can be eliminated.
A single tool replaces the roughing and finishing endmills, dramatically
reducing cycle time and increasing productivity.
Extra tool position is gained on the machine.
Eliminates the need to keep a large amount of stock.
4 flutes: 2 serrated plus 2 continuous flutes.
Excellent performance and tool life.
Suitable for all types of steel. Excellent performance in machining titanium,
inconel, stainless steel and high temperature alloys.

Finishred FS-B44 4 Flute End Mill

Guhring GV120 Heavy Duty Stub Drills HSS-Co

Manufactured to Type GV120 DIN1897.

Series 329

Allied Maxcut Series 1 and 1.5 Holders

Diameter range: 17.53 to 24.38mm.

For all dimensional specifications please refer to our catalogue.

Taper Shank

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Sherwood Fine Pitch Ripper Cutters Threaded Shank HSS-EV

Multi flute ripper cutters. Manufactured from sintered HSS-EV extra vanadium steel. Knuckle form, h8 tolerance, standard length. Dimensions to DIN 1835D.

Regular Series

SwissTech Heavy Duty Stub Drills HSS-Co Cobalt

Heavy duty drill made of high quality cobalt material with excellent heat resistance. For drilling steels up to 1,400N/mm2, stainless steel, heat resistant steels and bronze. Ideally suited for volume production on automatics. Point angle: 135. Helix angle: Normal. Web thickness: Strengthened. Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to DIN1897RN.

Series 2010

3 Flute Straight Shank Countersinks

These three flute Sherwood 90 countersinks are manufactured from HSS-E cobalt steel with a ground finish. They are suitable for deburring and chamfering most metals and plastics. Manufactured to BS328:Part 5:1983.

For all dimensional specifications please refer to our catalogue.

90 Degrees

Sherwood® Printed Circuit Board Drills Solid Carbide

Suitable for drilling through printed circuit boards. Shank diameter: 3.175mm, 38mm overall length. Manufactured to DIN1899.

For all dimensional and technical specifications please refer to our catalogue.

Sherwood Taps

Sherwood HSS Taps are the general purpose option for thread cutting in most materials including steel, some stainless steels, cast irons and non-ferrous materials such as Aluminium, Brass and many others.

Manufactured with precision ground flutes for producing accurate thread forms, Sherwood Taps are available in all the popular thread forms and as straight Flute `Hand` Taps in 3 leads, Fluteless, Spiral Flute, or Spiral Point Machine Taps and also Long Series.

Sherwood Tap dimensions conform to ISO529 apart from NPT Forms which conform to ANSI 94.9. Straight Flute and Fluteless Taps are manufactured with a standard Bright Finish whereas the Machine Taps have an Oxidised Finish for best results dissipating the heat build-up associated with these applications.

Thread Forms are Class 2 medium fit tolerance.

For all technical and dimensional specifications please refer to our catalogue.

Second Tap UNC (Unified Coarse) Straight Flute Ground Thread HSS

The Sherwood second tap is used after the taper tap has cut threads into the hole as far as possible. It tapers back 3 or 4 threads before a fully threaded diameter is reached. If threading a blind hole a Plug tap will be required to cut threads to the bottom of the hole.