Starrett Holesaws

Starrett diamond grit holesaws have a diamond coated cutting edge that is permanently bonded to a tough steel body, which provides the necessary clearance for cutting at high speeds. They will rapidly cut through reinforced plastic, germanium and other abrasives that may not be possible to cut with carbide holesaws.

Holesaw and Arbor sizes:
14-30mm - use Arbor XA1.
32-210mm - use Arbor XA2.

Holesaws Diamond Grit

Sherwood Drills Taper Shank HSS

General-purpose drills to drill steels with a tensile strength up to 1.000 N/mm2, cast steel, grey cast iron, malleable cast iron, nickel brass and graphite. Point angle: 118°, helix angle: normal, relief angle: normal, tolerance of diameter: h8. Manufacturing Standard: DIN345.

For all dimensional specifications please refer to our catalogue.

Series T100 (MT3) - Metric

Guhring GV120 Heavy Duty Stub Drills HSS-Co

Manufactured to Type GV120 DIN1897.

Series 329

SwissTech 2 Flute 42 High Helix Slot Drills Weldon Shank for Aluminium HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Shank cutting diameter to plus0.04 -0.0. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 15 Regular SHH-3WR HSS-Co 8%

Dimensions to DIN 844.

Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Inch

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Parting Off Tools

Right Hand. Available in Grades P40, P30 and K20.

Sherwood 2 Flute Slot Drills Threaded Shank HSS

Used for milling keyways and slots in one unit. Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Short Series S210T - Metric

WNMG

Suitable for External/Internal Toolholders.

SwissTech 2 Flute 42 High Helix Slot Drills Weldon Shank for Aluminium HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Shank cutting diameter to plus0.04 -0.0. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 15 Regular SHH-3WR HSS-Co 8%

Dimensions to DIN 844.

Walton 3 & 4 Flute Tap Extractors

Thoroughly remove all chips of the broken tap. insert the extractor fingers into the flutes of the broken tap, pushing them gently but firmly into position. Push the holder down until it touches the broken tap. slide the sleeve down until it touches the work. Apply a tap wrench to the square end of the holder. Twist forward and backward a few times to loosen, then back out the broken tap.