SwissTech High Helix Quick Spiral Drills for Aluminium HSS-Co 8%

High helix drills, to drill long-chipping materials like aluminium, aluminium alloys, copper and plastics. Point angle: 130. Helix angle: High. Web thickness: Normal. Relief angle: Normal. Tolerance of diameter: h8. Tolerance of shank: f11. Manufactured to DIN338RN.

Series 1012 - Metric

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

E2 Boring Bar Holders

Allied Maxcut Series 3 Inserts

For all dimensional specifications please refer to our catalogue.

GEN2 T-A HSS Super Cobalt AM200 Coated

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Brazed Tip Cranked Turning & Facing Tools

Left Hand. Available in Grades P40, P30 and K20.

Kennedy Holesaw Variable Pitch Bi-Metal HSS

Kennedy variable pitch bi-metal high speed holesaws feature a very aggressive cutting action, which gives a very smooth finish and substantial reductions in noise levels. Noise reduction is achieved by disrupting the harmonics produced when sawing certain materials and structures such as tubing and angle. An improvement in swarf clearance is also achieved.

Cutting depth: 28.5mm (1.1/8'').

Holesaw and Arbor sizes:
14-30mm - use Arbor K1 or K4.
32-210mm - use Arbor K2 or K10.

Dormer HSCO Jobber Drills

A901 HSCo PFX Alcrona Top Jobber Drill
High productivity "one-hit" drilling to 6xD
Alcrona Top coating for extended tool life.
Excellent performance across a wide range of materials.
Size Range: 1.5 - 16.0mm, 1/16” - 5/8”

Guhring GT100 Extra Long Drills HSS-Co 5%

High heat resistant drill with wide chip space for very deep holes in difficult conditions, such as when swarf congestion hinders the flow of coolant to the drill point or when tool overheating arises from other causes. For use in steels and cast steels of high tensile strength (not suitable for lubrication holes in crankshafts). Manufactured to DIN1869.

For all dimensional specifications please refer to our catalogue.

Series 619 - Metric

Sherwood® Knuckle Form Ripper Cutters

Sherwood® 'Rippal' 3 flute ripper cutters have centre cutting as standard and as they are manufactured from HSS-Co 8% they operate at higher speeds and feeds than conventional shank milling cutters, removing more metal per minute. The Sherwood® 'Rippal' cutter's unique geometry ensures a more efficient cutting action and reduced cutting time helps you to reduce costs and increase productivity. Power and workholding rigidity must be checked carefully before use as it is recommended that 'Rippal' cutters are used with consistent power feed rates to eliminate backlash.

Sherwood® 'Rippal' cutters are available polished or unpolished and with a weldon or combination shank.

930MP Series 3 Flute 'Rippal' Ripper Cutters Weldon Shank HSS-Co 8%

The 930MP 'Rippal' cutters have polished flutes making suitable for use when cutting aluminium to ensure optimum swarf removal.

Indexable Toolholder & Insert Sets

Tool supplied complete with 10 Carbide inserts, in a choice of P Grade for steels and general use, or K Grade for cast iron and non-ferrous applications. Inserts supplied will vary according to availability.

SDJC R/L

93° approach. Uses DC_T Inserts. For toolholder details see IND-106-4560K/4640K.

SwissTech Shank Milling Cutters

The latest enhancement of the SwissTech range, these cutters deliver excellent performance when cutting difficult materials, even at high speeds.

Manufactured from premium PM (Powder Metallurgy) tool steel, with an excellent cutting geometry. Designed for strength and rigidity, minimising vibration in high speed cutting applications and providing improved productivity.

These cutters are further enhanced by the SwissTech Peak Power coating, suiting dry cutting applications, having higher oxidization resistance and hot-hardness than conventional TiALN or TiCN coatings, withstanding the high thermal loads associated with high speed cutting applications.

Series 93 3 Flute End Mills HSS-E PM Coated

Centre cutting.
Weldon shank to DIN 1835B.
Shank diameter to h6.
Dimensions to DIN 844.

For all technical specifications please refer to our catalogue.