SwissTech Fine Pitch Ripper Plain Shank Q-Coat Carbide

Centre Cutting. To Manufacturers Standards. Cutting diameter to e8, Shank diameter to h6. ?Q-Coat? Coating has been specifically developed to give carbide cutters the ?edge? when faced with severe machining conditions. Materials up to 66 HRC. Dry cutting. Die and Mould machining. Reduced coolant usage and disposal. Up to 100% longer cutter life. Reduced manufacturing costs. A multi-layer coating capable of operating at higher speed and feed. Excellent oxidisation resistance. High speed machining. Surface hardness 3300HV. Surface coefficient against steel 0.25. Thickness of coating 305um. Maximum working temperature 850. Re-coating service also available.

For all technical and dimensional specifications please refer to our catalogue.

Series 82 Regular RFQ-3*PR Q-Coat

*Number varies according to the number of flutes.

Dormer Stub Drills

A920 - HSCo PFX Stub Drills
High productivity "one-hit" drilling to 3xD. Excellent performance across a wide range of materials. Parabolic flute design promotes constant chip flow.Size Range: 1.0-20.0mm. Manufactured to BS 323, DIN1897, ansi.

A920 - HSCo PFX Stub Drills - Inch

CNMG

Suitable for External/Internal Toolholders

Walton 3 & 4 Flute Tap Extractors

Thoroughly remove all chips of the broken tap. insert the extractor fingers into the flutes of the broken tap, pushing them gently but firmly into position. Push the holder down until it touches the broken tap. slide the sleeve down until it touches the work. Apply a tap wrench to the square end of the holder. Twist forward and backward a few times to loosen, then back out the broken tap.

Kennedy® Stub Length Drills Carbide

For drilling into steel, cast steel, cast iron, chilled cast iron, malleable cast iron, non-ferrous materials and abrasive plastic. Point angle: 118°, helix angle: 30°, tolerance of diameter: h7, tolerance of shank: h6. Manufactured to DIN 6539.

Tolerances:
Cutting Dia. plus 0.000mm - 0.015mm.
Shank Dia. plus 0.000mm - 0.030mm.

Kennedy® Carbide Stub Length Drills - Metric

Kennedy® Brazed Tip Turning and Boring Tools

Manufactured in three standard grades. (All sizes are nominal). Manufactured to ISO DIN BHMA Standards.
P40:
Roughing to heavy roughing of steel and steel castings using heavy feeds and low to medium cutting speeds. Also used under unfavourable conditions, particularly where intermittent cutting is involved. This grade is also suitable for planing operations and for machining manganese steel.
P30:
Carbide tipped tools are suitable for heavy duty turning and boring on all classes of steel. Suitable also for interrupted cutting and machining at low speeds and heavy feeds.
K20:
General-purpose tools for most applications. Ideal for machining cast iron, non-ferrous metals, bakelite etc. Combines wear resistance with toughness when rough turning at moderate cutting speeds. Suitable for high feed rates.

For all dimensional and technical specifications please refer to our catalogue.

Parting Off Tools

Right Hand. Available in Grades P40, P30 and K20.

Sherwood Solid Counterbore HSS-E

Used for milling of pre-drilled holes to allow bolt or cap head screws to lie flush with the component surface. Spiral, 3 flute. Medium duty. Manufactured to BS328:5:1983.

For all dimensional specifications please refer to our catalogue.

Spiral 3 Flute Plain Shank

Dormer HSCo Stub Drills

Excellent for drilling higher tensile, tougher materials
135° split point for improved precision and finish (over 1.5mm).
Manufactured to DIN1897.

HSCo Stub Drills - Series A117 - Metric

SwissTech 2 Flute 42 High Helix Slot Drills Weldon Shank for Aluminium HSS-Co 8%

Centre cutting. Weldon shank to DIN 1835B. Shank cutting diameter to plus0.04 -0.0. Available in HSS-Co 8% Uncoated (for general production machining), HSS-Co 8% TiCN Coated (extends cutter life and improves work material surface finish) and HSS-Co 8% TiALN Coated (dissipates and resists heat, reduces surface friction coupled with high surface hardness).

For all dimensional specifications please refer to our catalogue.

Series 15 Regular SHH-3WR HSS-Co 8%

Dimensions to DIN 844.

Allied Maxcut Series 0 and 0.5 Inserts

For all dimensional specifications please refer to our catalogue.

GEN2 T-A HSS Super Cobalt AM200 Coated