Sherwood Stub Drills HSS

General-purpose drills for use on automatics and turret lathes. Suitable for drilling steels, cast iron, alloy steel and malleable cast iron. Point angle: 118, Helix angle: Normal, Web thickness: standard, Relief angle: 10-20, Tolerance of diameter: h8, Tolerance of shank: f11. Manufactured to BS328:Part 1:1986/DIN338.

Series S100

Kennedy Industrial Power/Machine Saw Blades

6 Teeth Per Inch. Recommended for cutting thin cross-sections such as tubing, small bars and light angle iron. Because blades are relatively thin they should be used only on light machines.

HSS All Hard Powersaw Blades

Suitable for Section Width 13 to 38mm (1/2" to 1,1/2")

Dormer Jobber Drill Sets

Dormer's A002 Jobber Drill has a standard helix, it is right hand and has wider flutes for efficient chip removal. 118 point geometry. TiN coated on the tip for high wear resistance, lower friction and allows increased cutting speeds. Suitable for general-purpose drilling.
The Dormer A002 Jobber drill delivers the following features and benefits:
Improved web design optimises strength and rigidity and increases feed capability
Ground wide flutes allow for efficient chip evacuation
Optimised throughout the helix range for greater rigidity
Bright body improves application on ductile materials
Titanium Nitride coating focused on the working surfaces to resist flank and crater wear, and to provide low friction and increased performance
Special Dormer P.S. Point increases ease of penetration, improves hole size and provides accurate centering
General purpose engineering drills
Manufactured to BS328:Part 1:1986.

No.201 Drill 19 Piece Set 1.0-13.0mm

Dormer No.201 Drill Set contains in increments of 0.5mm.
Metric sizes:
1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10.0mm.

Sherwood 4, 6 & 8 Flute End Mills Threaded Shank HSS-Co

Used for profile milling and producing open slots. Bright finish. Flute Type : 30° Helix. Manufactured to BS 122: Part 4: 1980.

For all dimensional and technical specifications please refer to our catalogue.

Long Series Type E431T - Metric

A510 5.20mm HSS-TiN ADX S/S JOBBER DRILL

Marlco Litecut Keyway Push Broaches

Manufactured to BS4235;Part 1:1972 (normal fit Js9) and DIN6885 for Metric sizes, and BS46;Part 1:1958(1985) for Inch sizes. Precision made from high speed steel and simple to use with minimal set-up. The cutting geometry will suit most materials. Push broaches are designed for use in hand-operated or hydraulic mandrel presses, depending on load. Load per tooth, given in the tables, is based on a UTS of 400N/mm2 (approx. 25 tons/sq in). For other materials, adjust accordingly. It is important that broaches are reground when blunt and before damage occurs to the teeth. The use of cutting fluid is essential, and for steel, an oil with high pressure additives is recommended. Keyways from 2mm to 25mm width and bore diameters of 6mm to 95mm are possible. Both parallel and taper keyways can be cut by using the appropriate guide. Broach style L2 and L2M require the use of an extension shank which should be ordered separately. The shims specified for standard depth keyways can be adjusted to suit particular applications. Parallel broaches are listed and supplied as standard. Broaches for taper keyways are available to order.

For all dimensional and technical specifications please refer to our catalogue.

Litecut Keyway Push Broach

Series: L1. Nominal size: 1/8". Actual size (tolerance): 0.125/0.126. Body width: 5/16". Broach length: 8". Length of cut: 0.72" (min), 2.13" (max). Tooth pitch: 0.36. Depth of keyway on centre line: 0.063. No. of passes: 3. Number of shims x thickness required: 2 x 0.03. Load per tooth: 68. Weight: 0.10kg.

Sherwood® Slitting Saw Blades

Sherwood® HSS slitting saws are used for cutting metal, these small diameter saws are hollow ground to give the clearance necessary for deep cutting.

Sizes up to 1" diameter do not have key ways.

For all technical and dimensional specifications please refer to our catalogue.

Slitting Saw Small Diameter HSS

Kennedy® Thredfloer Fluteless Taps

Form rather than cut the thread in almost any ductile material. These include aluminium, brass, copper, carbon steels, zinc and magnesium alloys and even some stainless steels. The material is "cold formed" into the relevant thread and has the advantage of being a full form thread unlike normal cut tapped holes. This make the thread stronger. The forming operation does not create chips so swarf contamination and blockage is illiminated and tap breakage reduced. Because there is no consideration for chip evacuation, Thredfloer taps can be run at higher cutting speeds and reduced cycle times. Lubrication grooves are a feature of all Thredfloer taps of M3.0 and over. These allow lubrication to reach the end of the tap to maintain tool life and to prevent damage from "Hydraulic Blow Out".

Metric Coarse

HSS - EV. Oxide Finish. Tolerance 6H. Manufactured to DIN 371.

WNMG

Suitable for External/Internal Toolholders.

Butt-Welded Lathe Tools

Manufactured from top quality sintered steels. For use on a wide range of applications from roughing to finishing. Manufactured to BS1296:Part 3:1978.

For all dimensional and technical specifications please refer to our catalogue.

Internal Screw Cutting Tools - No.50A RH

Rake and Clearance angles:
Top rake: 5.
Front clearance: 6.
Approach angle: 0.
Trail angle: 1.
Side clearance: 1.