Indexa-Seiki? Multi-Pro Spot Drill & Chamfer Mill

A spotting drill with all the advantages of indexable inserts - reduced tool maintenance time, increased performance, lower inventory cost and no regrinding requirements. The insert clamping method ensures accurate and secure location with quick change-over times. Multi-pro has a unique geometry which allows cutting over the centre line, using carbide, without chipping of the cutting edge. This versatile tool may be used to 'spot' holes prior to drilling, as a means to guide the drill and keep the hole straight, to keep size and accurately position, relative to the datum.
NB. The 118 inclusive tool is recommended for 'spotting' prior to drilling with 118 point drills. Countersinks may be produced prior to drilling to provide a corner break on a drilled hole, a chamfer conforming to drawing specifications, a lead in for a subsequent tapping operation, or a full countersink to accommodate a screw head. Corner chamfers on edges, contours and bores can be machined as light de-burring operations or full depth chamfers. Multi-pro may be used to produce vee grooves for fluid channels, locations for round components and grip pattern or serrations on jaws and clamp pads.

"Multi Pro Standard"

Indexa-Seiki? ER Collet Chucks

Indexa-Seiki? ER chucks are the most versatile tool holding system for any operation that utilises a round shank cutting tool in a machining centre. Used in conjunction with Indexa-Seiki? ER collets the cutting tool is centralised in the chuck and if all the ER system components have been maintained correctly, this should result in increased tool life, higher feed rates, better work piece accuracy and enhanced work piece finish. Typical applications include drilling, milling, tapping, reaming and boring.

BT40-ER32-70 Collet Chuck

The Indexa-Seiki? BT40-ER32-70 collet chuck is balanced to 12,000rpm. Max TIR 0.010mm.

For all technical and dimensional specifications please refer to our catalogue.

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

E2-1 Boring Bar Sleeves

Indexa-Seiki ER Single-Angle Collets

Collet Dimensions:
Capacity 3.0-13.
(D)21mm x (L)31.5mm.

ER20

Indexa-Seiki R8 Collets for Bridgeport Machines

Used directly in the machine spindle for general purpose milling and drilling operations, collets have dedicated bores for specific cutter shank sizes.



Available in bore sizes:
Metric: 3, 6, 8, 10, 11, 12, 14, 16 and 20mm.
Inch: 1/4, 3/8, 1/2, 5/8/ 3/4 and 7/8??.

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

E2-3 Morse Taper Sleeves

XP-90C Weldon End Mills

Positive 90 approach milling cutter, using size 10/16 inserts allowing depth passes and high feed per teeth. Torx screw allows for good chip ecacuation. Plasma Ion coating offers longer tool life and greater hardness that is more resistant to wear. Through coolant as standard.

XP-90C End Mills For AP_T 16 Inserts

Indexa-Seiki? External Toolholders - COMBINATION CLAMP

For further technical and dimensional specifications please refer to our catalogue.

MVJN - Left Hand

93 Approach for negative 35 rhombic inserts

Indexa-Seiki? Screw-On External Toolholders

For further technical and dimensional specifications please refer to our catalogue.

SCLC - Right Hand

95 Approach for for 7 positive 80 rhombic inserts.

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 1.0-16.
(D)26mm x (L)35mm.

ER25