Indexa-Seiki Tapping Collets

Slipping clutch type. To suit Indexa-Seiki tension and compression type tapping chucks.

For all technical specifications please refer to our catalogue.

DIN SZ2

Indexa-Seiki ER - Collet Chucks

The Indexa-Seiki ER Collet chuck is manufactured as part of Europe's most popular collet system. The collapsing collet design can be used for a range of diameters and maintains concentricity for drilling and milling. Long reach options are also available to give access into deep recesses. Balanced to 12,000rpm. Max Tir 0.010mm. (BT BT-MAS 403)



To BT-MAS 403

Indexa-Seiki Tru-Loc Milling Chucks

The mechanical advantage provided by the 'roller lock' mechanism produces a high clamping force, along the full length of cutter shank. The force is applied evenly and so enables the chuck to hold cutters within 0.010mm at 100mm from chuck nose concentricity, giving improved component surface finish, holding better workpiece tolerances, reducing vibration and prolonging tool life. Manufactured from special alloy steel, heat treated to close hardness tolerances. Internal seals protect against entry of swarf and dirt. Tru-Loc milling collets with back stop adjustment screws ensure quick and easy cutter pre-setting and replacement, eliminating tool creep. A range of milling chucks for finishing and semi-finishing applications, with accurate tolerances and high quality surface finish.

Using the Tru-Loc Milling Chuck - when tightening the chuck use the recommended wrench and tighten fully - but without means of extra leverage. N.B. The gap between the locking ring and body may vary between 0 & 3mm dependent on cutter shank size and collet used. Maintenance: To get the best performance from this Tru-Loc milling chuck please ensure it is serviced on a regular basis by a qualified agent. It is recommended that this is at least once every twelve months. Failure to do this may affect the performance of the chuck and/or invalidate any guarantee. Collet reference PSC/PSCa.

Tru-Loc Milling Chuck IS40 Shank

Indexa-Seiki SL - Sidelock Adaptors

For Weldon shank cutters, adaptors and tapping chucks. Manufactured to stringent quality standards.

Standard Length

To DIN69871/A

Indexa-Seiki Indexable Tooling Spares

Within the Index-Seiki range of indexable tooling spares you will find insert screws, Torx keys, shims, clamps and pins to fit the Index-Seiki toolholder you're using.

Indexa-Seiki Flatted Shank Adaptors

Allows existing Weldon Shank Side Lock Arbors to hold smaller shank cutters.

Flatted Shank Adaptor

Indexa-Seiki Indexable Tooling Spares

Within the Index-Seiki range of indexable tooling spares you will find insert screws, Torx keys, shims, clamps and pins to fit the Index-Seiki toolholder you?re using.

Indexa-Seiki? Screw-On External Toolholders

For further technical and dimensional specifications please refer to our catalogue.

SCLC - Right Hand

95 Approach for for 7 positive 80 rhombic inserts.

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburised and hardened. Surface hardness of 58 - 60HRC. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

E2-1 Boring Bar Sleeves

Indexa-Seiki ER - Single Angle Collets

Collet Dimensions:
Capacity 2.0-20.
(D)33mm x (L)40mm.

ER32