Hydraulic Puller/Separator Set

10 ton capacity hydraulic ram with tommy bar. Suitable for agricultural machines, garage and industrial use.



Contents: 1 x hydraulic ram. 3 x 4", 6" & 8" puller legs. 1 x twin head. 1 x triple head. 1 x 50mm ram extension. 1 x 100mm ram extension. 2 x 200mm main rods. 2 x 230mm extension rods. 1 x 75 - 105mm separator. 1 x bolt. 1 x ram ring. 1 x ram nut. Blow moulded storage case

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

Industrial Reversible/Double Ended Adjustable

Thin/2 Jaw Mechanical Pullers

Manufactured from forged steel, with thin jaws for access where the clearance behind the component is limited.
086000 Spread: 75mm. Reach: 75mm.
086100 Spread: 150mm. Reach: 150mm.
086200 Spread: 150mm. Reach: 225mm.
086300 Spread: 150mm. Reach: 225mm.

Spare Jaw

Spare Jaws to suit Kennedy Mechanical Pullers. Supplied individually.

Hydraulic Separator Set

For removing bearings, gears, sprockets & bushes. 10 ton capacity hydraulic ram with tommy bar. Metal storage case.

HS7 105-150mm & HS11 75-105mm

Both sets contain: 1 x hydraulic ram. 1 x separator. 2 x 200mm main rods. 2 x 230mm extension rods. 1 x beam. 1 x ram nut. HS7 (only) also contains 1x 80mm push plate 1x 50mm ram extension. 1x 100mm ram extension.

Spare Jaw

Spare Jaws to suit Kennedy Mechanical Pullers. Supplied individually.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Mechanical Separator Set

For removing bearings, gears, sprockets & bushes. Metal storage case.

30 - 75mm

Contents: 1 x 7" thrust bolt. 1 x 30-50mm separator. 1 x 50-75mm separator. 2 x 80 & 100mm main rods. 2 x 90 & 110mm. extension rods. 1 x beam.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

External Mechanical 2 Long Jaw Puller

Manufactured from drop forged hardened alloy steel. 3 position extra long legs to be used where access is limited. The puller legs are securely located on the bearing by screwing down the tapered nut to lock the arms in position. The legs are then retracted with the bearing by turning the t-bar to extend the thrust bolt on to fixed shaft.
Spread: 10 - 50mm
Reach: 300mm