Separator & Puller Combination Set

Manufactured from forged alloy steel. Taper jaws allow the separator to be used where access behind the component is too restricted to use normal pullers.



155200 Makes four hydraulic pullers and one separator. In lockable metal case. Spread 50 to 150mm. Reach 50/100/150mm.

Hydraulic Pullers

Ram Extension Bars

Hydraulic Pullers

Have a simple, grease filled ram instead of the mechanical force screw. This produces more power easily & efficiently. The spring loaded plunger provides direct, non- twisting application of thrust safely.

Thin Jaw Hydraulic Pullers - Combination Set Kit

Manufactured from forged steel, with thin jaws for access where the clearance behind the component is limited.
186504 Spread: 225mm. Reach: 225mm. Extension: 50/150mm. Contains components to make up to five different hydraulic and one mechanical thin jaw puller.In metal box.

Internal Extractor Kits

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Thin/2 Jaw Mechanical Pullers

Manufactured from forged steel, with thin jaws for access where the clearance behind the component is limited.
086000 Spread: 75mm. Reach: 75mm.
086100 Spread: 150mm. Reach: 150mm.
086200 Spread: 150mm. Reach: 225mm.
086300 Spread: 150mm. Reach: 225mm.

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

Industrial Reversible/Double Ended Adjustable

Mechanical Puller Set

Suitable for GM, Ford and Chrysler vehicles. Also suitable for removing pulleys and fly wheels.

SWP9 Steering Wheel

Contents: 1 x yoke, 1 x thrust bolt. 1 x thrust cap. 2 x 75mm screws (5/16" x 24 UNF). 2 x 75mm screws (3/8" x 16 UNC). 2 x 90mm screws (5/16" x 18 UNC). 1 x plastic storage tray.

Mechanical Pullers - 2 Jaws - Industrial Reversible/Double Ended

The double ended reversible/double ended drop forged steel jaws, are heat treated for strength and durability. They can be used internally or externally.
083100:
Spread: 200mm.
Reach: 140mm.

Industrial Reversible/Double Ended

Hydraulic Separator Set

For removing bearings, gears, sprockets & bushes. 10 ton capacity hydraulic ram with tommy bar. Metal storage case.

HS7 105-150mm & HS11 75-105mm

Both sets contain: 1 x hydraulic ram. 1 x separator. 2 x 200mm main rods. 2 x 230mm extension rods. 1 x beam. 1 x ram nut. HS7 (only) also contains 1x 80mm push plate 1x 50mm ram extension. 1x 100mm ram extension.