Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Mechanical Pullers - 2 & 3 Jaw Industrial Reversible/Double Ended

The double ended reversible/double ended drop forged steel jaws, are heat treated for strength and durability. They can be used internally or externally. 082700/082705 - Spread: 150mm. Reach: 80mm.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Kennedy Seal Repair Kit

To suit the Kennedy 10 Ton Hydraulic Ram (KEN-503-7200K). N.B. Hydraulic Ram not included.

Thin/2 Jaw Mechanical Pullers

Manufactured from forged steel, with thin jaws for access where the clearance behind the component is limited.
086000 Spread: 75mm. Reach: 75mm.
086100 Spread: 150mm. Reach: 150mm.
086200 Spread: 150mm. Reach: 225mm.
086300 Spread: 150mm. Reach: 225mm.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Internal Extractor Kits

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Long Reach Mechanical Pullers - 2 jaw - Industrial Reversible/Adjustable

The points at which the jaws are attached to the pulling frame, are adjustable providing more pulling options.
083300:
Spread: 350mm.
Reach: 380mm.

Internal & External Puller Set

Fully chromed carbon steel hammer and T-bar for smooth striking action. Supplied in a blow moulded storage carry case.



Fully hardened & chromed carbon steel slide hammer with a 1.2kg weight. Slide hammer design for removing bearings from blind housings. Suitable for use where a shaft or other solid surface is not available for a thrust bolt or hydraulic ram to push against. The bearing is removed by the impact action of the slide hammer weight hitting the stop at the end of the bar. The puller legs are securely located on the bearing by screwing down the tapered nut to lock the arms in position. Blow moulded case.

Internal Extractor Kits

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.