Mechanical Puller - 2 & 3 jaw Industrial Kits Reversible/Double Ended/Adjustable

Manufactured from chrome vanadium steel. Each kit contains the components to assemble a 2 or 3 jaw external or internal puller. The legs can be set at 2 different height positions.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Separator & Puller Combination Set

Manufactured from forged alloy steel. Taper jaws allow the separator to be used where access behind the component is too restricted to use normal pullers.



Set contains components to make five different puller/separator combinations: 10mm, 89mm reach three jaw internal or external puller. Thin jaw, two jaw puller internal or external. 55mm diameter separator.

Hydraulic Pullers

Have a simple, grease filled ram instead of the mechanical force screw. This produces more power easily & efficiently. The spring loaded plunger provides direct, non- twisting application of thrust safely.

Thin Jaw Hydraulic Pullers - Combination Set Kit

Manufactured from forged steel, with thin jaws for access where the clearance behind the component is limited.
186504 Spread: 225mm. Reach: 225mm. Extension: 50/150mm. Contains components to make up to five different hydraulic and one mechanical thin jaw puller.In metal box.

Hydraulic Ram

Applies exceptional direct thrust with ease. Can ve used with bearings up to 140mm.

Mechanical Puller Set

For harmonic balance removal, timing gears & other parts with bolt circle diameters from 38mm to 117mm (11/2" to 45/8"). Ductile steel yoke.

HPB9 Harmonic Balance

Contents: 1 x yoke. 1 x thrust bolt. 1 x ram nut. 3 x 75mm screws (3/8" x 24 UNF). 3 x 75mm screws (3/8" x 16 UNC). 1 x plastic storage tray.

Thin/2 Jaw Mechanical Pullers

Manufactured from forged steel, with thin jaws for access where the clearance behind the component is limited.
086000 Spread: 75mm. Reach: 75mm.
086100 Spread: 150mm. Reach: 150mm.
086200 Spread: 150mm. Reach: 225mm.
086300 Spread: 150mm. Reach: 225mm.

Kennedy Hydraulic Ram

10 ton capacity grease filled hydraulic ram with spring loaded plunger. Provides direct non-twisting application of thrust that is more effective and secure than a mechanical thrust screw. Fully threaded body allows for quick and easy height adjustment.

Internal Extractor Kits

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

Industrial Reversible/Double Ended Adjustable