Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

External Mechanical 2 Long Jaw Puller

Manufactured from drop forged hardened alloy steel. 3 position extra long legs to be used where access is limited. The puller legs are securely located on the bearing by screwing down the tapered nut to lock the arms in position. The legs are then retracted with the bearing by turning the t-bar to extend the thrust bolt on to fixed shaft.
Spread: 10 - 50mm
Reach: 300mm

Long Reach Mechanical Pullers - 2 jaw - Industrial Reversible/Adjustable

The points at which the jaws are attached to the pulling frame, are adjustable providing more pulling options.
083300:
Spread: 350mm.
Reach: 380mm.

6 Way Hydraulic Puller Set

10 ton capacity hydraulic ram with tommy bar. Supplied with 3 position puller legs covering a spread of 50 - 250mm and reach of 0 - 250mm. Can be used as a 2 or 3 legged puller with the same head.



Contents: 1 x combination head. 1 x hydraulic ram. 3 x 3 position puller legs. 6 x leg connectors. 6 x screw nuts, bolts & washers. 1 x 32mm ext. rod. 1 x ram nut. 1 x blow moulded storage case.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Hydraulic Pullers

Have a simple, grease filled ram instead of the mechanical force screw. This produces more power easily and efficiently. The spring loaded plunger provides direct, non-twisting application of thrust safely.

Hydraulic Micro Puller - 3 Jaw

The jaws are manufactured from drop-forged steel with independent leaf springs for positive location. Suitable for the rapid removal of small bearings. Spread: 19 - 45mm.Reach: 73mm.

Bearing Separator & Puller Sets

Bearing separator with two interchangeable thin jaw puller legs. Puller has a 75mm spread and reach. The separator has a maximum diameter of 55mm and a reach of 115mm.

Hydraulic Pullers

Ram Extension Bars

Hydraulic Pullers

Have a simple, grease filled ram instead of the mechanical force screw. This produces more power easily & efficiently. The spring loaded plunger provides direct, non- twisting application of thrust safely.

2 and 3 Jaw Kit

Combination twin/triple leg puller kits. Complete with ram extension. 155000: Spread: 150mm. Reach: 150mm. Extension: 50mm. Contains components to make up 4 different pullers. In metal box.