Hydraulic Pullers

Have a simple, grease filled ram instead of the mechanical force screw. This produces more power easily and efficiently. The spring loaded plunger provides direct, non-twisting application of thrust safely.

Hydraulic Micro Puller - 3 Jaw

The jaws are manufactured from drop-forged steel with independent leaf springs for positive location. Suitable for the rapid removal of small bearings. Spread: 19 - 45mm.Reach: 73mm.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Internal Extractor Kits

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

Mechanical Pullers - 2 & 3 Jaw Industrial Reversible/Double Ended

The double ended reversible/double ended drop forged steel jaws, are heat treated for strength and durability. They can be used internally or externally. 082700/082705 - Spread: 150mm. Reach: 80mm.

Kennedy Mechanical Pullers

Kennedy three leg mechanical pullers are used for the removal of gears, ball races, bearings, pulleys and sprockets from drive shafts. With a range of reach capacities available (75 to 200mm) selecting the puller for the job could not be simpler. All have double-ended reversible legs so that they can grip internally or externally depending on your requirement.

Always use a three leg puller whenever possible. As they will grip the component being pulled more securely and the load is more evenly distribution across the three legs, this helps to make removal of the component easier and safer.

To select the correct Kennedy puller for the job you will need to determine what spread and reach capacity is required; spread capacity this is the width of the part to be removed and the reach capacity depth of the part to be removed.

For the full range of Kennedy hydraulic pullers and other Automotive tools please refer to our catalogue.

Internal/External Three Leg Mechanical Puller

Long Reach Mechanical Puller - 2 Jaw

Used for the removal of gears, ball races, bearings, pulleys and sprockets from a drive shaft. With reach capacities of 75mm, 100mm, 150mm and 200mm. All sizes have double ended, adjustable, reversible legs and can be used for internal and external applications. Selection. Always use a 3 jaw puller whenever possible. This produces better load distribution across the jaws and easier and safer removal of the part. Determine what 'spread' is needed this is the width of the part to be removed. The reach capacity is determined by the depth of the part to be removed.

Industrial Reversible/Double Ended Adjustable

Internal Extractor Kits

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.

"Multipull" Blind Housing Puller

For the removal of blind housing bearings without the need to dismantle machinery or remove the running shaft. Positive seating allows even tension on the inner and outer bearing rings reducing resistance. The stabilisers reduce sideways movement and self centres the puller. The three sets cover a range of ISO bearings, if there is no ISO reference on the bearing refer to the puller spread and adaptor.



098000 - ISO designation: 6004-6010, 6004-6015. Reach: 125mm. Adaptor diameter: 5.5 - 8mm.098100\t - ISO designation: \t6299-6205, \t6200-6211 & 6212-6222. Reach: 415mm. Adaptor diameter: 5.5 - 12.5mm.098200\t - ISO designation: \t6300-6302 Reach: 490mm. Adaptor diameter: 16 - 31.75mm.

Mechanical Puller Set

Suitable for GM, Ford and Chrysler vehicles. Also suitable for removing pulleys and fly wheels.

SWP9 Steering Wheel

Contents: 1 x yoke, 1 x thrust bolt. 1 x thrust cap. 2 x 75mm screws (5/16" x 24 UNF). 2 x 75mm screws (3/8" x 16 UNC). 2 x 90mm screws (5/16" x 18 UNC). 1 x plastic storage tray.

Split Collet Internal Bearing Extractors

The collets are precision machined, ideally used with sliding hammer assembly. For removing gears, bearings, pinions, oil seals when conventional pullers cannot be used. Collets close down to allow passage through a bore and then "wind" out to grip the blind side of the component.