Heavy Duty Push-Pull Clamps

Features: These clamps are of exceptionally robust construction featuring cast and machined handles and bases. The clamps are designed with a low plunger height and with the mechanism guarded within the base to avoid finger traps. Specification: The bases of all models are machined S.G. iron castings. The plungers are of steel, and their precision ground diameter runs in a close-tolerance hole in the base casting. All axles are of hardened steel and run in either the S.G. iron of the handle, or in the close-toleranced holes of hardened parts. All models are supplied with a steel setscrews finished chemi-black.

Vertical Industrial Toggle Clamps

Designed to improve performance in fabrication and engineering clamping applications. The rapid clamping/unclamping made possible by the use of toggle clamps can greatly reduce machine/operator 'down-time' during all stages of production. Clamping Capacity - the forces stated are the maximum loads that can be applied without causing permanent deformation. Due to leverage ratios, the holding capacity will be greatest at the point on the bar nearest to the handle of the clamp and forces stated have been achieved at this point.

'U' Bar (Adjustable) Type

Flanged Base

FOLDABLE BOXES

Foldable storage boxes made from tough grey polypropylene. Compatible in size with the Euro Containers (use the same lids) and can be stacked with or without lids. Simple to collapse for space saving storage when not in use.
Available in two sizes:
400x300x220mm
600x400x220mm

Precision Ground Flat Stock (1000mm)

The dimensional stability of ground flat stock combines with other useful characteristics including excellent resistance to cracking during heat treatment compared with other, more highly alloyed, cold work tools. Relatively soft and easy to machine. High wear resistance after heat treatment. Holds a good cutting edge. Suitable for EDM machining.
Typical applications: widely used in precision tools, machine knives, gauges, jigs, templates, punches, dies and machine parts.
The Cost Cutting Stock: extensive range of widths and thicknesses enables the selection of an appropriate size of ground flat stock to minimise material and machining costs.

Manufactured from BS4659 B01 grade steel equivalent to AISI 01 and Werk. No. 1.2510.
Chemical analysis range:
Carbon 0.90 - 1.00%
Silicon 0.40%
Manganese 1.00 - 1.20%
Chromium 0.50 - 0.70%
Tungsten 0.50 - 0.70%
Vanadium 0.05 - 0.25%

Chemical analysis typical:
Carbon 0.95%
Silicon 0.40%
Manganese 1.20%
Chromium 0.55%
Tungsten 0.55%
Vanadium 0.15%

Metric sizes

Tolerances:
Thickness: -0.00mm/+0.050mm.
Width: -0.00mm/+0.200mm.
Length: -0.00mm/+5.000mm.

Matlock™ Parts, Component and Tool Storage Bins

Matlock™ high strength Polypropylene storage bins are designed to solve your storage problems, they are suitable for small to large component or part storage. The versatile Matlock™ storage bin can be interlocked side by side, nested on top of each other, hung on steel louvred panel (supplied separately) or using riser rods (supplied separately) they can be stacked on top of each another, this functionality allows you to create the storage system to satisfy your specific requirement.

Matlock™ storage bins are available in seven sizes and a choice of four colours blue, green, red and yellow and can be fitted with label holders (supplied separately).

For all dimensional specifications and accessories please refer to our catalogue.

Label Holders for Matlock? Plastic Storage Bins

These plastic label holders fasten over the front of the Matlock™ storage bins so that an identification label can be displayed for the contents of the storage bin.

Fixture Components

Material: Body - Medium Carbon Steel EN198. Ball - Through Hardened Steel EN 31. Hardness: Body - HRC 32 - 38. Ball - HRC 62. Surface Finish: Ball - Hardened and Ground

FC16 - Clamp Set Screw

Ball Point

Fixture Components

Material: Body - Medium Carbon Steel EN198. Ball - Through Hardened Steel EN 31. Hardness: Body - HRC 32 - 38. Ball - HRC 62. Surface Finish: Ball - Hardened and Ground

FC17 - Clamp Set Screw

Ball Point

Chuck Keys

Suitable for use with all industrial keyed chucks.

Document Workstations

Perfect for supervisory or general workshop use, these units combine secure storage with a sloping worksurface. All steel construction with epoxy powder coated grey/blue finish with reinforced, lockable doors, two adjustable shelves, two internal drawers and a sloping writing surface.

Tool Station

1130 x 500 x 550mm (H x W x D)

Silver Steel

For tool room and general engineering. Applications include screwdrivers, punches, shafts, axles, pinions, pins, die posts, instrument parts, model parts, taps and drills for mild steel, engraver tools. High carbon content means that it can be hardened to give high wear resistance and chromium content adds strength and hardness.

Manufactured from
BS1407:1970 grade steel.

Typical hardness:
207-237HB with 285HB maximum.

Tensile strength:
45/55 T.P.S.I. (700/850 N/mm2).

Surface finish:
Better than 0.6 microns (25 micro inch) CLA (Centre Line Average).

Chemical analysis range:
Carbon 0.95 - 1.25%
Silicon 0.40% max
Manganese 0.25 - 0.45%
Phosphorous 0.045% max
Sulphur 0.045% max
Chromium 0.35 - 0.45%

Chemical analysis typical:
Carbon 1.13%
Silicon 0.22%
Manganese 0.37%
Phosphorous 0.014%
Sulphur 0.018%
Chromium 0.43%

Inch round sizes

Tolerances:
Below 1" plus/minus 0.00025".
1" up to and including 2" plus/minus 0.00050".