Resettable Flashback Arrestor

Flashback arrestors are designed to offer complete protection, for both operator and equipment, combined with high flow performance and ease of use. Designed and manufactured to fully comply with BS EN 730-1, providing complete protection for all oxygen and fuel gas equipment requirements.

GA-D99 Resettable - Oxygen

Dinse Type Cable Plugs & Sockets

With positive locking connection, to prevent accidental disconnection and good external insulation to prevent water penetrating the joint. Dinse compatible panel sockets and machine/surface mounted plugs & sockets also available.

2% Thoriated Red Tungsten Electrodes

Most commonly used tungsten electrode. Suitable for both AC and DC welding on carbon, stainless steels, nickel, copper and titanium alloys. Preferred for their longevity and ease of use.

Kennedy 3.2mm 2% Thoriated Red Tungsten Electrodes

2% thoriated tungsten electrodes (AWS classification EWTh-2) contain a minimum of 97.30% tungsten and 1.70 to 2.20% thorium. They are the most commonly used electrodes today and are preferred for their longevity and ease of use. Thorium increases the electron emission qualities of the electrode, which improves arc starts and allows for a higher current carrying capacity. This electrode operates far below its melting temperature, which results in a considerably lower rate of consumption and eliminates arc wandering for greater stability. It also features a lower level of weld contamination than other electrodes. Unlike pure tungsten, these electrodes are only for specialty type AC welding (thin gauge aluminum or materials less than .060-in.), but they are exceptional for DC electrode negative or straight polarity on carbon and stainless steel, nickel and titanium applications.
During manufacturing, thorium is evenly dispersed throughout the electrode. This evenness allows the electrode to maintain a sharpened edge, the ideal electrode shape for welding thin steel. Sharpening the electrode point, however, should be done with great care. Thorium is radioactive; therefore, you must always follow manufactures warnings, instructions and the MSDS (Material Safety Data Sheet) for its use.

Kennedy Flux Cored Gasless Wire

General-purpose Mig wire with self-shielding flux core, allowing it to be used without the need for a separate shielding gas. Designed and packaged specifically for use on Kennedy Dual Mig welders, Mini Migs, Migmates etc. For welding mild steel and C-Mn steels such as boilers, tanks, pipework, machinery, vehicle chassis fabrication. 0.8mm diameter. Random wound and not layer wound. Available in 2 reel sizes 0.45kg and 0.90kg.

Flux Cored Gasless Wire

Electrodes for Mild Steels

Arc welding rods for mild and medium tensile steels

Supercito 7010S ('Low Hydrogen')

Basic coated, all positional rods. Applications: for steel plate structural steels, pipe work and forgings. Ideal for repairs of casting and machinery, compensates for dilution effect of poor steels. Often used where rutile deposits may be at risk from cracking.
N.B. Suitable for AC (70V minimum open circuit) and DC. Optimum rooting operability is obtained using DC-.

RED insulated liner FOR WIRES
with retainer 1.0/1.2mm

TO SUIT: MB15 MB25 MB36

Aluminium Tig/Gas Welding Rods

Sifsteel Stainless 308LBS 2901 : Part 2 : 1990 18/8-308L 308S92 AWS A/SFA 5-9-93.
Low carbon austenitic filler rod for welding steels of similar composition (18% Cr, 8%Ni). Use with argon shielding gas or argon/5% hydrogen.

Lightweight A-FN Cutting Nozzles

For use with lightweight cutting attachments.

2017 A-FN nozzle diameter 1/32". Plate thickness (mild steel) 3 - 6mm.
2018 A-FN nozzle diameter 3/64". Plate thickness (mild steel) 6 - 20mm.
2019 A-FN nozzle diameter 1/16". Plate thickness (mild steel) 20 - 50mm.

Extension Tubes

For use between handle and burner for extending the reach. Can also be used in conjunction with multiple burner adaptors Nos. 1122 and 1123.

Murex Heavy Duty Swaged Welding Nozzles

For use with Saffire 5, 4 & 3. Plate thickness refers to mild steel.

Murex Saffire 5 Cutting Attachment

For use with No.5 shank and ANM/PNM nozzles.