Process & Heating Nozzles

Fully compatible with most heavy duty welding shanks and blowpipes. Including 1144, 1143, 2010, Saffire 5, 4, 3, NM250, NM400, Citogas HDT200, NMC200. Size 13 suitable for Saffire 4 and 3 only.

Acetylene Gouging Nozzles - A-GNM

Oxygen/Propane Cutting Kit

An oxygen & propane cutting kit capable of cutting up to 300mm (12”).

Contents:
18” - 90º nozzle mix cutting blowpipe.
Single stage 10bar/150psi oxygen plugged regulator.
Single stage 4bar/58psi propane plugged regulator.
Oxygen thermal in-line flashback arrestor.
Fuel gas thermal in-line flashback arrestor.
Pnm short nozzles.
Nozzle cleaners.
Cup type spark lighter.
Drop forged combination spanner.
Cup goggle 2" round shade 5 - EN166 & EN175.
Red plastic carry case.
*Requires separate hose set.

040951

Primus 2000 Cylinder Accessories

Full flame burner for large soldering, brazing and heating jobs.

Solent Flaw Detector Inspection System

Fast reliable method for visually inspecting and spot-checking surfaces of welds, exotic alloys or standard metals, highly stressed structural members, critical castings, shafts, gears, spindles, and any other hard part where identification of surface flaws is essential. Detects flaws such as cracks, pin holes, welding laps and porousness either during manufacture or on site. A three part system. SFD-501C is a cleaner. SFD-502C is a dye penetrant. SFD-503C is a developing fluid that reacts with the dye in SFD-502C to show small cracks in the weld. Each part supplied in an ozone friendly 500ml aerosol.

Flaw Detector Developer

White film to highlight any faults which have been detected when using Flaw Detector Penetrant. The product should be removed using Flaw Detector Cleaner Spray once cracks have been found and marked.

Reusable Lugs

With arc cable.

MAP/Pro 399g Gas Cylinder - 3.5536

Disposable MAPP Pro Gas Cylinder for use with Rothenberger Quick Fire, Super Fire 2 and Micro Fire Torches. Cylinder Size 399g.



Based on a stabilized mixture of methylacetylene (propyne) and propadiene. MAPP gas is safer than acetylene; There is no 15 psi limit and it can to use on board ships and in mines. delivers higher temperatures than propane. Although acetylene has a higher flame temperature (3160 C, 5720 F), MAPP has the advantage that it requires neither dilution nor special container fillers during transport, allowing a greater volume of fuel gas to be transported at the same given weight, and it is much safer in use.

Autotorch Brazing System

A portable bronze brazing system using only a single cylinder of propane. Automatic piezo-electric ignition plus interchangeable burners.

Burners

No 4103 giving the smallest, No 4105 the largest, flames. The burners must be used at 4 bar pressure and should not be turned down. If a smaller flame is required a smaller burner must be used.

Gas & Tig Welding Rods

General purpose brazing or bronze welding rod. Suitable for brazing and bronze-welding of sheet, tube and extruded sections in all types of fabrication work, involving steel, cast iron, copper and its alloys.

Sifbronze No.1 - BS1845 CZ6 1453 C2

Ultra Gas Canister

A blend of Propane, Butane, Acetone and Propene to achieve a flame temperature of more than 2100 degrees Celcius! Simply screw the canister into the threaded fitting inside the tool to install. Gas canisters to suit the Sievert 3380 Portable Soldering Iron.

Parweld Mig Torch Accessories

Also compatible with Binzel Torches.