Walter Titex Production Jobber Drills HSS-Co 5%

For high tensile and work-hardening materials, stainless steels (austenitic) (300 series), heat resistant steels,
titanium, hard bronze, special alloys.
Manufactured to DIN 338.

Series A1244 - Metric

HSS Plain Shank Dovetail Cutters (Single Angle Cutters)

Bright finish. Flute type: 30° Helix. Manufactured to BS 122: Part 4: 1980.

45° Corner Angle - Metric (Form C)

For all dimensional and technical specifications please refer to our catalogue.

Sherwood HSS Plain Shank Corner Rounding Cutters

Designed to produce convex corner radii. For milling structural, carburising and heat treated steel up to 900N/mm2.
Manufactured to works standards.
5° RH Flutes.
Bright finish, straight helix.
Radii tolerance: ± 0.005”.

Metric

Dormer Taps

Dormer MTT-X Series taps are manufactured from HSS-X1 Steel with Bright finish, they are right Hand Cutting.

Manufactured to ISO 529
Spiral Point for threading through holes.
Taper lead to DIN form B.
Tapping tolerance to 6H.
Max Depth 2.5 x D.

For all technical and dimensional specifications please refer to our catalogue.

HSS-Co 8% Cobalt Long Series Milling Cutters 2 Flute

Centre cutting, used for profile milling, milling keyways and producing open slots. Surface treatment: bright finish.
Flute type: 30° Helix. Overall dimensions to DIN 844. Plain shank to DIN 1835A.

Long Series

WNMA

QX505 (ISO K05-K15) Coated. Used for finishing, semi finishing and medium roughing of Cast Irons including Malleable and Nodular Irons, at high speed.



Suitable for Internal/External Toolholders

Kennametal KC9125 Indexable Turning Inserts

(P20 - P35 CVD coated). The optimum cutting grade for machining steel in the upper cutting speed range. The polished chipbreaker gives the cutting edge maximum protection against chip strike, reduces friction temperature and results in an improved surface finish. This grade has well-adjusted wearing and toughness properties, cobalt enriched material with multi-layer coating.

CNMG

Kennedy Rotary Masonry Drill Bits

Tungsten carbide tipped with roll forged flutes. A general-purpose mortar and masonry drill bit suitable for workshop and maintenance. Manufactured to DIN 8039.

Extra Length

Available in 300mm to 400mm length.

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Marlco Litecut Keyway Push Broaches

Manufactured to BS4235;Part 1:1972 (normal fit Js9) and DIN6885 for Metric sizes, and BS46;Part 1:1958(1985) for Inch sizes. Precision made from high speed steel and simple to use with minimal set-up. The cutting geometry will suit most materials. Push broaches are designed for use in hand-operated or hydraulic mandrel presses, depending on load. Load per tooth, given in the tables, is based on a UTS of 400N/mm2 (approx. 25 tons/sq in). For other materials, adjust accordingly. It is important that broaches are reground when blunt and before damage occurs to the teeth. The use of cutting fluid is essential, and for steel, an oil with high pressure additives is recommended. Keyways from 2mm to 25mm width and bore diameters of 6mm to 95mm are possible. Both parallel and taper keyways can be cut by using the appropriate guide. Broach style L2 and L2M require the use of an extension shank which should be ordered separately. The shims specified for standard depth keyways can be adjusted to suit particular applications. Parallel broaches are listed and supplied as standard. Broaches for taper keyways are available to order.

For all dimensional and technical specifications please refer to our catalogue.

Litecut Keyway Push Broach

Series: L2M. Nominal size: 10mm. Actual size (tolerance): 10.000/10.018. Body width: 14.30mm. Broach length: 305mm. Length of cut: 31.8mm (min), 104mm (max). Tooth pitch: 15.9. Depth of keyway on centre line: 3.40. No. of passes: 4. Number of shims x thickness required: 2 x 1.25, 1 x 0.75. Load per tooth: 250. Weight: 0.74kg.