Starrett Holesaws

Starrett tungsten carbide tipped sheet metal holesaws are ideal for cutting high alloy and stainless steels, non ferrous light metals and reinforced fabrics. The tough tungsten carbide tipped teeth, have a positive cutting angle to provide fast and efficient removal of chips and swarf, cutting depth is 13mm.

Sheet Metal Holesaws Tungsten Carbide Tipped

Starrett tungsten carbide tipped sheet metal hole saws deliver the following advantages:
Ideal for production cutting.
Tungsten carbide tipped teeth provide superb product life and cutting performance.
High cutting accuracy.
Replacement pilot drills are available.
Complete assembly - there is no requirement to purchase a separate arbor and pilot drill.
Safety stop at the base of the hole saw prevents drilling beyond maximum cutting depth.
Cutting depth 13mm (1/2").

Indexa-Seiki VDI Toolholders

Manufactured to DIN 69880. Suitable for use in NC lathes with VDI fixing disc. Features: All tools are fully carburized and hardened. Surface hardness of 58-60HRc. Tensile strength above 1000N/mm2. Surfaces blued; seat, parallel shank and shoulder ground. Tools can be adjusted in-situ on radial and axial toolholders. Seat shim allows two tool sizes to be used with one toolholder. Ball regulator (bullseye) provides easy coolant control.

D1 Axial & Radial

Guhring Machine Chucking Reamers Intermediate Diameter HSS-E

Available in diameters ranging from 2mm to 10mm in increments of 0.01mm. Made from HSS-E steel with a bright finish, left hand spiral flute. For all ferrous and non-ferrous metals and hard and soft plastics. For use on CNC machines, producing high quality reamed holes. Manufactured to DIN 212 and DIN 2172 section 1.

Shank diameter equals cutting diameter - 0.025mm.
dia 2.00 - dia 2.65 / dia 2.66 - dia 10.00 H9.

Diameter Tolerances (to H7)
Up to 5.5mm: plus 0.004mm minus 0.000mm
Above 5.5mm: plus 0.005mm minus 0.000mm.

Code numbers are determined by the nominal diameter. Delete the decimal point; create a four figure number by preceding the figures with a zero, if required. All codes finish with the letter A, i.e. 3.60 becomes 0360A.

For all technical specifications please refer to our catalogue.

Allied Maxcut Series 0 and 0.5 Holders

Diameter range: 12.98 to 17.65mm.

For all dimensional specifications please refer to our catalogue.

Taper Shank

Dormer Machine Taps

Dormer machine tap ranges have been designed for use with a high quality floating tool holder. For synchronous tapping on CNC machines with a rigid tapping cycle, Dormer SynchroFlex tool holders are recommended for a precisely defined minimum compensation in order to maximise machine performance. This is particularly important for larger sizes of spiral flute taps.

Available in spiral point for through holes and spiral flute for blind holes with 45 spiral angle. The three radii profile, with a constant rake angle all along the flute, is specially designed to give an optimum performance and chip evacuation in materials being threaded.
Surface Treatment
Special gold finish with bright flutes/thread, or steam tempering (blue) guarantee a smooth cutting action with less build up on the cutting edge.

Manufactured from HSS-XS1 premium quality vanadium powder steel and HSCo for superior toughness and edge strength, to give a high resistance to wear and long tool life.

All taps are available in Metric thread form initially. Thread forms Metric Fine, UNC, UNF and G will be stocked from September 2010.
Short Thread Length
The short thread length means low torque and better chip evacuation.
Thread Depth
Threading to depths of up to 2.5 x Diameter.

EP01 Series Spiral Point Metric Machine Tap

Dormer Spiral Point Machine Taps for through holes. Taper lead to DIN form B.
With Blue finish.
Tapping tolerance to 6H.
Max depth 2.5 x D.

Guhring Production Jobber Drills HSS-Co 5%

High heat resistant drill with wide chip space. Suitable for drilling alloyed and unalloyed steels and castings with a high tensile strength over 800N/mm2. Particularly suitable for drilling hot and cold rolled steels. Manufactured to DIN338.

Series 658 - Metric

OSG Taps

OSG type 1066 machine taps are manufactured from 3% Vanadium Super Grade High Speed Steel. Increasing the vanadium content improves the toughness without making the tap brittle. This means the tap has a greater resistance to work generated heat, which prolongs the life of the cutting edge.

Spiral Point taps are suitable for threading through holes.

Manufactured to ISO 529: 1975.

For all technical and dimensional specifications please refer to our catalogue.

Spiral Point Taps Metric HSS-EV

Granlund Carbide Size 1 Counterbores

Type H. Carbide K40 micrograin. Tolerance P8.

Counterbores H with a diameter of 50mm and larger are all made with a driving lip. These sizes should be used in the appropriate type M toolholder.

For further specifications please refer to our catalogue.

SwissTech Heavy Duty Drills HSS-Co 8% Cobalt TiN Coated

Heavy-duty drill used to drill steels with a tensile strength up to 1,400 N/mm2. Stainless steels, heat and acid resistant steels and phosphor bronze. TiN coating provides longer tool life. Point angle: 135. Helix angle: Normal. Web thickness: Strengthened. Relief angle: Normal. Tolerance of diameter: h8. Supply unit. All diameters - 1 pce. Manufactured to DIN338RN.

Series 1033 - Metric

Granlund Size 1 Insert Drills

Type B HSS Tol. h8 flute 25mm.

When combining insert drills with countersinks, the drill must break through the work piece before secondary cutting commences and must not be used for blind holes.

For all technical specifications please refer to our catalogue.