Kennedy® Aluminium Oxide Cloth

Superflex Aluminium Oxide is resin bonded over resin on a very flexible J-weight blue twill cloth. Moisture resistant and electrostatically coated for polishing flat and contoured surfaces of most materials.

Rolls

Roll size: (W)50mm x (L)50 Metres. Available in several grades.

Kennedy® Portable Task Light

Portable Task Light using an energy saving 28W 2D fluorescent bulb that generates the same light as halogen but using far less energy. Eliminates common problems associated with halogen bulbs such as high heat and bulb blow out when knocked. Tough polycarbonate case and virtually shatterproof lens. Ideal for all trades. IP44 Rated. 3M cable.

Portable Task Light

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Round Tree

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® 3kW 6-Bar Thermo-Quartz Heaters

6 bar thermo-quartz heater that is ideal for spot heating, heating only the solid object and not the air. Switchable between half and full heat 1.5 - 3kW. Silent running and lightweight. Dimensions: 890 x 300 x 460mm (HxDxW). Weight: 14kg.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® Sharpening Stones

Aluminium Oxide man-made abrasive which is extremely tough enabling high speed penetration of high tensile materials without causing excessive fracturing. This resistance to fracturing makes it a versatile material suitable for general sharpening and honing applications.

Square Aluminium Oxide

A range of tough general-purpose sharpening stones able to give keen, even cutting edges on all straight edge cutting tools. Consistent and uniform cutting edges ensure fast cutting and longer tool life.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B71. Grade: RA120. Diameter: 16mm. Length: 2.4mm. Max. rpm: 60,000. Weight per 10: 40g.

Kennedy® Flexible Backing Pads

Suitable for use with all portable and air disc sanders. Recommended for use with Kennedy® abrasive discs.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Inverted Cone

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 27 Depressed Centre Grinding

For use with all portable angle grinders. Not to be used for wet grinding. Optimum angle for use 25° to 35°. Grade A30/AS30 - for general purpose use on metals. INOX - for use on Stainless steel (iron, chlorine and sulphur free).