Kennedy Rotary Masonry Drill Bit Set

Tungsten carbide tipped with roll forged flutes. A general-purpose mortar and masonry drill bit suitable for workshop and maintenance. Manufactured to DIN 8039.

Standard/Medium Length 7 Piece Set

Contents:
No.10 x 85mm, No.12 x 100mm, No.14 x 100mm, No 16 x 120mm, No.20 x 120mm, No.24 x 150mm (medium length) & No.26 x 150mm (medium length).

Kennedy® Tripod Site Lights

Halogen bulb head fitted with 5 metre cable and plug. Heavy duty steel tubing. Extends to over 8 feet.

Foldaway

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Inox BF Cut-Off Discs

Iron, chlorine and sulphur free. Thin 1.0 mm discs that enable you to achieve a uniquely clean cut in the shortest possible time whilst using minimum of force. vibration-free cutting, no thermal bluing and no burring. For use on thin sheet metal, steel cable, thin-walled profile sections, stainless steel pipes and non-ferrous metals. Max. operating speed: 13280 r.p.m.

Kennedy® Wet or Dry Silicon Carbide Paper

Silicon Carbide is waterproof-resin bonded to paper suitable for wet and dry production polishing and finishing of a wide range of materials including metals, plastics, paintwork, ceramics etc.

Wet or Dry Paper Sheets

Size: (W)230mm x (L)280mm. Available in several grades.

Kennedy® Router Cutters

Cutter for deep mortising and grooving. Staggered cutting edges give good chip clearance enhancing quality of cut.

Two Flute Staggered Tooth Bits

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HSS - Heavy Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T218A)
Application: steel 1.5 - 4mm, aluminium 1.5 - 4mm.
Blade: HSS heavy duty, wavy set tooth form. For cutting curves. Tooth pitch: 1.2mm.

Effective length: 48mm.

PAck of 5.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'A' Shape. Shank Diameter 6mm

Shape A31. Grade: RA46. Diameter: 35mm. Length: 25mm. Max. rpm: 25,000. Weight per 10: 340g.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'B' Shape. Shank Diameter 3mm

Shape B65. Grade: RA120. Diameter: 3mm. Length: 3mm. Max. rpm: 100,000. Weight per 10: 20g.

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 42 Depressed Centre Cutting Discs

For use with all portable grinders/cut-off machines. Not to be used for grinding. Grade A24 - for general-purpose use on metals.