Seam Splitter Set - 3Pce

Ideal for separating spot-welded panels during repairs.
Stainless steel coated Chrome Vanadium with through tangs shafts allow use with hammers.
Dual material soft grip handles for comfort and control.
Includes 90, curved and straight seam splitters.
Cushioned handle absorbs any shock from hammer blows.
Made from super tough alloy steel.
Pack size: 400(H) x 175(W)mm
Gross Weight: 0.94kg

90 Seam Splitter
* Easily separates hard-to-reach spot welding or bonding panels. Best used for quarter panels, rockers and any other pinch welds.
* Sharpened on three sides, the sharp end allows for penetration between the panels and the edges allow for side impact to lever the panels.
* Blade width: 25mm
* Blade Depth: 65mm
* Overall length: 240mm

Curved Seam Splitter
* For quarter panels, rockers and any other pinch weld.
* Sharpened on two sides, the sharp end allows for penetration between the panels and the edges allow for side impact to lever the panels.
* Blade width: 25mm
* Blade Depth: 18mm
* Overall length: 300mm

Straight Seam Splitter
* For quarter panels, rockers and any other pinch weld.
* Sharpened on two sides, the sharp end allows for penetration between the panels and the edges allow for side impact to lever the panels.
* Blade width: 25mm
* Overall length: 300mm

Seal Repair Kit

To suit the Kennedy Heavy Duty 1/2 Ton Transmission Jack (KEN-503-7160K) illustrated. N.B. Jack not included.

Brake Calliper Spreader

For retracting brake calliper pistons can be used with 1/2 " sq drive ratchet and 21mm hex wrench or spanner and is suitable for use on most cars and motorcycles. Constructed from hardened steel with phosphate finished spreader plates for corrosion protection.

Hydraulic Ram

Rugged construction with a heavy duty retrn spring. Chrome plated piston inhibits rusting.

Pull type

5 ton capacity.
15cm stroke.
1/4" NPT thread size.

Seal Puller Tool

Two size tips allow you to remove oil or grease seals from virtually anything including wheel bearings, transmission housings, etc. Hardened and tempered carbon steel shank and head with oxidised finish tips. Chrome plated shank for protection against corrosion. Impact resistant square section handle for secure grip even when greasy. Overall length: 310mm (12 1/4")

Kennedy Hydraulic Bench Press - 10 Tonnes

Ideal for pressing, bending and extruding.
Welded steel frame with two end brace for stability.
Fully adjustable work bed providing flexibility and convenience.
Detachable pump and ram allowing hydraulics to be used for other purposes when the press is not being used.
Hydraulic gauge is included.
Built for tough daily use in industrial and automotive workshops.
Capacity: 10 Tonnes.

Lever operated vacuums

For use in hand lift applications only. Multiple vacuums used on a single load can only improve handling. If using more than one vacuum tool the ratio of maximum lift capacity does not increase. To lift heavier weights a larger vacuum must be used. All are fitted with a rubber suction which will not damage contact surface during the lifting action. For use on glass, tiles, plastic or other smooth surfaced non-porous material and can also be used for pulling out dents. Hand lift only, must not be used in conjunction with mechanical lifting equipment.



2 x 120mm diameter rubber suction cups. Maximum lift: 70kg.

Hydraulic Hand Pump

Rugged construction. Internal overload valve prevents it from being used beyond its rated capacity. Operates in a vertical and horizontal position.

Single speed

Pressure rating 1000psi (700bar).
Usable oil capacity 600cc.
1/4" NPT thread size.
Carrying handle for easy portability.

Wax Injector Gun

WIG100
Pneumatic tool for spraying and injecting wax underseal into areas that are difficult to access, such as door cavaties, inside box section chassis and around wheel arches. Has a 1 litre container with a 1/4 " NPT connection, operates from 90-145psi (6-10bar) air pressure with an air compsumption rate of 380ltr/min and a Vacuum (maximum) 550mm HG.
Supplied with 900mm spray hose and hanging hook.

Kennedy Hydraulic Bottle and Trolley Jacks

Kennedy Hydraulic bottle jacks have large cast iron bases with a steel housing and lift cylinder, that has an adjustable notched load saddle. Each jack is fitted with an overload protection valve. Two piece pumping handle also operates hydraulic release.

For use on a firm level surfaces. DO NOT work under the raised vehicle until another means of support, such as axle stands are in place

GS and TUV approved.

For axle stands see order codes: KEN-503-5520K and KEN-503-5530K.

Hydraulic Bottle Jacks

Model number: B845
Maximum load: 8 Metric Tonnes.
Height range: 230 to 457mm Min/Max.
Max saddle adjustment: 80mm.
Weight: 5.75kg.

(Load ratings are Metric Tonnes i.e. 1 tonne = 1,000kg).
Supplied with spare seals.