Kennedy® Velcro-Backed Sanding Discs

No spanners required to change discs. 100% of sanding disc can be used, material removal rate is therefore increased. Can be repeatedly removed and re-applied again and again. Unaffected by dust or moisture. Aluminium oxide abrasive "resin-bonded over resin" to Velcro backed paper suitable for wood, plastics, ceramics etc.

Plain (No Holes)

Diameter: 125mm.

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 42 Depressed Centre Cutting Discs

For use with all portable grinders/cut-off machines. Not to be used for grinding. Grade A24 - for general-purpose use on metals.

SIP Trade 3.0hp Dust Collector – Four Bag

01956
For up to 3 Machines
Triple input capable of running one, two or three woodworking machines simultaneously. Powerful 3hp induction motor gives smooth, long lasting performance. Very sturdy steel construction. Mounted on free running castors for increased manoeuvrability. Quick release stops. Inlet blanking adaptors supplied. Connection hose not included. 2 year warranty.

Specifications:
Supply: 230v (13amp).
Motor: 2230w (3hp).
Fan diameter: 300mm.
Inlet diameter: 1x150mm or 3x100mm (with adaptor).
Air flow: 6963 m3/hour.
Bag capacity: 2x153L.
Weight: 59kg.

Hitachi 18V Impact Wrench

Charge time: 60min.
No-load speed: 1500/min.
Impact rate: 2000/min.
Max torque: 480Nm.
Capacity (bolt): M12-M22.
Capacity (HT bolt): M12-M16.
Overall length: 264mm.
Weight: 3.4kg.

Kennedy® Festoon Site Kit

110V 22 metre cable with 10 lamp holders which are designed to suit ES (screwed) lamps. Lamp holes are spaced at 2 metres with a maximum wattage of 60W per lamp holder. Supplied with wire guards and plain bulbs.

Festoon Site Kit - 110V

Flexovit Grinding Wheels

GC: For offhand grinding of low tensile materials and non ferrous metals, also suitable for carbide tool grinding.

Type 1, Plain

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'A' Shape. Shank Diameter 6mm

Shape A38. Grade: RA60. Diameter: 25mm. Length: 25mm. Max. rpm: 35,000. Weight per 10: 200g.

Kennedy® Router Cutters

Tungsten carbide tipped cutters to cut slots in rails to accept panels or for cutting slots in frames and doors for 'weather' feature fittings. Arbors are supplied separately.

Three Tooth Slotting/Biscuit Jointing Cutter

Kennedy® M2 Multi-Tooth Milling Cutters

For use with all multi-tooth milling cutters with 6mm bore. Pilots locate into pre-drilled pilot holes ensuring positional accuracy of the cutter. Suitable for "blind" or "through" pilot holes, pin will retract into cutter adaptor on "bottoming".

Pilot Pins

Bore diameter: 20mm.
Overall length: 156mm.

Engis Hyprez Oilstones

Manufactured from carefully graded abrasive particles, mixed with the appropriate bonding agents and fired in electric or gas ovens to produce a stone suitable for roughing out cavities and dies to commercial finishes.

Hyprez H.Y. Semi-Hard Aluminium Oxide

Oil filled, this stone is designed to minimise loading. Length: 150mm.