Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 41 Flat Reinforced Cutting

For use with all portable angle grinders. 180mm to 230mm discs can also be used on circular saws, and 300 to 350mm discs are for use with chop saws/cut-off machines, subject to bore compatability. Not to be used for wet cutting.
Grade A24 - For general purpose cutting on metals.
Grade C24 - For general purpose cutting on stone.

Kennedy® Router Cutters

Designed with large chip clearance at base. Suitable for hinge recessing and shallow flat bottom apertures.

Two Flute Hinge Mortising Bits

Kennedy® Wire Wheels & Brushes

Industrial rotary wire wheels & brushes are available as a comprehensive range including circular brushes, shaft mounted arbor style and de-carbonising brushes for use with power tools, machine tools and flexible drives.

Circular Brushes - Shaft Mounted

Suitable for use in power drills. Most suitable for hard to reach areas and grooves. 6mm Shanks. 30 SWG

Kennedy® Router Cutters

With ball bearing guide. Moulding suitable for items such as cabinets and table mantle tops.

Two Flute Roman Ogee Bits

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness. Operating speed range is 6000-40000rpm.

Cylindrical Ball Nosed

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Sharpening Stones

Silicon Carbide man-made abrasive with very hard, sharp particles. This makes it ideal for non-ferrous metals, hard surfaces, alloys and cemented carbides. Also used on stone, marble, glass and plastics. A superior abrasive that is able to penetrate and cut quickly with only light pressure being applied.

Square Silicon Carbide

A range of tough general-purpose sharpening stones able to give keen, even cutting edges on all straight edge cutting tools. Consistent and uniform cutting edges ensure fast cutting and longer tool life.

Kennedy® Wet or Dry Silicon Carbide Paper

Silicon Carbide is waterproof-resin bonded to paper suitable for wet and dry production polishing and finishing of a wide range of materials including metals, plastics, paintwork, ceramics etc.

Wet or Dry Paper Sheets

Size: (W)230mm x (L)280mm. Available in several grades.

Kennedy® Sanding Sheets

Industrial aluminium oxide sanding paper is "glue" bonded and suitable for use with hand sanding blocks and orbital sanders.
Fine, Medium and Coarse grades available.

1/2 Sheet

Dimensions: (W)115mm x (L)280mm. Pack of 25.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 6mm

Shape W171. Grade: RA60. Diameter: 8mm. Length: 19mm. Max. rpm: 36,000. Weight per 10: 100g.

Kennedy® "T" Type Shank Jigsaw Blades

High teeth per inch (TPI) blades are slower cutting and produce a better edge finish. Low teeth per inch blades are faster cutting but produce coarser cuts. Different materials will also give different edge finishes depending on the material and direction the grain. When cutting certain metals, lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw base plate reducing the gap around the blade and reduces the splinter area. Another technique is to score a guide line on the wood, this creates a pre-cut line that must then be followed accurately. Anothertechnique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made. 'T' Style or bayonet fitting as used by AEG, Atlas Copco, Bosch, Dewalt, Elu, Hitachi, Holz-Her, Kobe, Makita, Metabo.

HCS - Medium Duty (Pack 5)

Jigsaw Blade (Equivalent to Bosch T101D)
Application: wood 60mm, plastics 30mm.
Blade: HCS medium duty, tapered and ground.
Tooth pitch: 4.0mm.

Effective length: 75mm.

Pack of 5.