Bosch Style Chisels

Suitable for air and electric hammers and breakers, for all classes of work.



For Bosch: USH27, USH28, 11304, 11308, 12314. 29mm Hex Shank with Single Flat.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® Extension Cables for Site Use

Waterproof spring loaded socket caps. Available as 1.5mm2 core cables rated to 16A over six hours and 2.5mm2 core cables rated to 32A over six hours (except KEN-282-2400K, rated at 16A). Plugs and sockets conform to BS 4343 : 1968.

240V 1.5mm Core

Kennedy® Depressed Centre and Flat Reinforced Grinding Discs

All Kennedy Depressed Centre and Flat Reinforced Cutting wheels now carry the "oSa" (The Organisation for the Safety of Abrasives) mark of approval. "oSa" is an association of the world's leading abrasives manufacturers. In France, it is mandatory to use only oSa-certified rough grinding wheels and cutting wheels. Similarly in Germany and Italy, it is strongly recommended that abrasive products conform to the relevant EN standards. "oSa" marked products are guaranteed to meet or exceed the highest worldwide safety standards, including those of the Comite Europeen de Normalisation (CEN), the European standards body that issues EN standards, and of ANSI in the USA.

Type 41 Flat Reinforced Cutting

For use with all portable angle grinders. 180mm to 230mm discs can also be used on circular saws, and 300 to 350mm discs are for use with chop saws/cut-off machines, subject to bore compatability. Not to be used for wet cutting.
Grade A24 - For general purpose cutting on metals.
Grade C24 - For general purpose cutting on stone.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Long Series

Shank dia.: 19mm/3/4".
Depth of cut: 50mm.
Bore: 6mm.
Overall length: 85mm.

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Jigsaw Blades

Manufactured from high quality steels to meet the demands of most industrial and DIY applications. Supplied display carded. High teeth per inch (TPI) blades will be slower cutting and produce a better edge finish. Low teeth per inch blades will be faster cutting but produce coarse edges on the workpiece. Different materials will also give different edge finishes depending on the make up of the material and direction of cut in relation to the direction of the grain. When cutting in some metals lubricant or grease may be required to reduce friction and dissipate heat. Various techniques can be employed to prevent splintering of cut edges on wood, especially laminated materials. These include the use of an anti-splinter guard. This is a plastic insert that locates in the jigsaw baseplate reducing the gap around the blade and reducing the splinter area. Another technique is to score a guide line on the wood creating a pre-cut line that must then be followed accurately. The last technique is to place adhesive tape over the proposed cut line, this holds the material in place whilst the cut is being made.

Straight Shank Suitable for Fein, Wolf and Kress. HCS - Medium Duty (Pack 5)

Capacities: Wood - 50mm, Plastic - 30mm. Tooth pitch: 4.0. Effective length: 75mm. Tapered & ground teeth. Equivalent to Wolf 91480.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'A' Shape. Shank Diameter 6mm

Shape A35. Grade: RA46. Diameter: 25mm. Length: 10mm. Max. rpm: 38,000. Weight per 10: 180g.

Kennedy® Fibre Discs

Resin fibre, aluminium oxide sanding discs are designed for a wide range of industrial applications. High speed penetration of tough and high tensile materials combined with long disc life and optimum flexibility ensure Kennedy sanding discs give first class performance every time. Recommended for use with all portable grinders and sanders. Available in a choice of grades and in diameters of 100mm, 115mm, 127mm or 178mm.

115mm Diameter x 22mm Bore (Max 11,000rpm)

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Ball Shape

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.