Kennedy® Spider Pod 3-Way 110V 16A Splitter

3x 16amp 110V sockets, tough water resistant housing, ideal for on-site use.

Kennedy® Economy Emery Cloth

The emery abrasive particles are bonded by a high strength glue to a flexible J-weight blue twill backing cloth. The backing cloth allows the abrasive sheet to conform to the shape of the item being worked on, ensuring the abrasive action is always where you require it. Suitable for general-purpose, light duty workshop use.

Rolls

Roll size: (W)50mm x (L)50 Metres. Available in several grades.

Kennedy® Economy Emery Cloth

The emery abrasive particles are bonded by a high strength glue to a flexible J-weight blue twill backing cloth. The backing cloth allows the abrasive sheet to conform to the shape of the item being worked on, ensuring the abrasive action is always where you require it. Suitable for general-purpose, light duty workshop use.

Rolls

Roll size: (W)25mm x (L)50 Metres. Available in several grades.

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 6mm

Shape W217. Grade: RA46. Diameter: 25mm. Length: 10mm. Max. rpm: 38,000. Weight per 10: 40g.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.
N.B. - 3mm Shank

Conical 14

Cut 9 - Chipbreaker
Chipbreaker fast stock removal for improved control and reduced chips for use on hard materials, i.e. steel alloy 50RC, 60RC, carbon and cast iron.

Kennedy® Router Cutters

General purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two Flute Straight Plunging Bits

Kennedy® M2 Multi-Tooth Milling Cutters

Proven value and success based upon the low energy required to cut more holes accurately with extended tool life. The cutter is designed to enable a faster feed rate with lower cutting resistance, resulting in consistency of finish and tolerance.

Short Series

Shank dia.: 19mm/3/4".
Depth of cut: 25mm.
Bore: 6mm.
Overall length: 60mm.

Kennedy® Router Cutters

With ball bearing guide. To trim plastic or laminate facings. Used extensively in cabinet making and shop fitting. Suitable for straight or curved work.

Two Flute Flush Trimming Bits

Kennedy® Mounted Points and Wheels

Suitable for portable die and straight hand grinders. All points are aluminium oxide with "rubenite" as standard for all general purpose grinding and deburring on steels and most metals. Silicon carbide grade (suitable for stone/non-ferrous grinding) available on request. Shank diameters are metric as listed below with inch sizes available on request. Maximum speeds are quoted assuming that collet to back of point does not exceed 12.7mm (1/2") and are for guidance only.

'W' Shape. Shank Dia. 3mm

Shape W149. Grade: RA120. Diameter: 4mm. Length: 6mm. Max. rpm: 100,000. Weight per 10: 20g.

Kennedy® Carbide Burrs

Suitable for deburring and polishing of cast iron, cast steel, carbon steel, alloy steel and stainless steel etc. up to HRC65 hardness.
Operating speed range: 6000-40000rpm.

Round Tree

Cut 3 - Rapid Cut
For use on softer non-ferrous and plastic materials i.e. aluminium, fibreglass, plastics, hard rubber and zinc alloy.